1.23. Let the signal input to a galvanometer be xş(t) = 0 t≤ 0 x(t) = Kt t> 0 in which K is a constant. (a) Find the expression for galvanometer response x,(t), assuming that the galvanometer is calibrated for static readings. (b) Show that the error î‚ — ï§ approaches a constant value. S (c) What would you estimate to be the optimum damping ratio in this galvanom- eter operation?

1.23. Let the signal input to a galvanometer be xş(t) = 0 t≤ 0 x(t) = Kt t> 0 in which K is a constant. (a) Find the expression for galvanometer response x,(t), assuming that the galvanometer is calibrated for static readings. (b) Show that the error î‚ — ï§ approaches a constant value. S (c) What would you estimate to be the optimum damping ratio in this galvanom- eter operation?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure (a) and figure (b) illustrate the signal x(t) and w(t). Given the signal p(t) as follows:
Q1. (a) (b) Signal y(t) is given as in Figure 1. Signal y(t) is going through an operation of time shifting and scaling to become signal b(t). If signal b(t) = y(-3). y(t) M -2 -1 Figure 1 (i) sketch signal b(t) (ii) explain the effect on the signal after went through the operations Signal b(t) is the input to the system as shown in Figure 2. Illustrate signal at Point A, Point B and Point C. b(t)- b(t). 23 4 Mixer Mixer A Adder + B Figure 2
(b) Figure Q1(b) shows the step response for a second-order system. Find its peak time and percentage of overshoot. Hence, obtain its transfer function. 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0. 6 10 12 14 16 18 20 22 24 Time (s) Figure Q1(b) Response
2. Consider the signal f(t) shown in Figure 2.9. Express the four signals displayed in Figure 2.10 in terms of transformations of f(t).
i need ans within 15 minutes my best wishes ton
In Figure (1) and Figure (2) illustrate the signal x(t) and w(t). Given the signal p(t) as follows: n() = [=(-;+1) - w»] Sketch the signal p(t) and show the stps clearly. Sketch the odd and even part of p(t). (iii) Determine whether the signal p(t) is an energy signal or power signal. (i) (ii)
A pulse with a duration of N = 5 with an amplitude of 1 5 The following are the zero crossings of the DTFT for $$0, W1 = and W2 = Note w2 > W1 Round off your answer to two decimal places.
Q1: A/ Determine the values of Power and Energy for the following signal: 1(t) = e-#u(t) -2t
Q: Explain why the envelop detector cannot demodulate the over-modulated signal . Discuss how to demodulate the over-modulated signal.
Q1 (a) A signal d(t) is given in Figure Q1(a). Express p(t), q(t) and s(t) in terms of d(t). (ii) q(t) as shown in Figure Q1(a)(ii) )P 1 1 Figure Q1(a) 1 1 3 Figure Q1(a)(ii)
Find the differential equation(s) that model the system. Can it be represented by a single differential equation between Vin and Vout?
For the system unit step response shown below where ss = 54 and t = 6 the system can be modelled by a process with pure time delay and a 1st order. Determine the time constant of the approximated 1st order SS 0.63ss- 3t Answer: 60 10t x The correct answer is: 42.00