a) Design a magnitude digital Comparator that compares two 2-bit unsigned binary numbers find out whether one binary number is equal, less than, or greater than the other binary number. The circuit has two 2-bit inputs A and B respectively and has three outputs, one A>B, one for A = B, and one for A

a) Design a magnitude digital Comparator that compares two 2-bit unsigned binary numbers find out whether one binary number is equal, less than, or greater than the other binary number. The circuit has two 2-bit inputs A and B respectively and has three outputs, one A>B, one for A = B, and one for A

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Please answer all subparts I will rate it..
Write your solutions in detail and legible
a) Convert the decimal number - 184 into a signed binary number using (1) sign-magnitude method (2) 1's complement method (3) 2's complement method b) If the above decimal number is positive , that is + 184, then convert it to a signed binary number using 1 's complement method c) Do the following binary subtraction: 101001110.01111- 010011110.10011
Let A = ajao and B = b¡bo be two-bit binary numbers. A and B can take on values from 0 to 3 (for example, A = 2 when a1ao = 10. Let C be a two bit binary number whose value equals the magnitude of the difference A – B. We have C = c1c0 = |A – B|. (This means that if B is larger than A then you consider B-A.) You are to design a circuit which accepts A and B (i.e., a¡ aob¡bo) as inputs and outputs the result C = c¡c0. The circuit thus has four inputs and two outputs. For example, the circuit should output c1co = 10 when ajao = 01 and bibo = 11 (C = 2 when A = 1 and B = 3). - Your pre-lab needs to include all items requested in the following steps (plus those requested in the pre-lab handout): 1. After reading through the complete lab, write a description of the expected behavior of the system you will design. 2. Draw a truth table describing the behavior of the circuit. The truth table should show the inputs: aj aobibo (in this order) and the outputs: c1Co · 3. Write the canonical SOP…
1. Gray code to Binary converter: Gray code is one of the codes used in digital systems. It has the advantage over binary numbers that only one bit in the code word changes when going from one number to the next. (See Table 1). Design a combinational circuit with 4 inputs and 4 outputs that converts a four- bit gray code number into an equivalent four-bit Binary number. Use Karnaugh map technique for simplification. Use LogicWorks for pre-lab demonstrations. Select the library "7400dev.clf* in the Parts Palette and then select the XOR chip 74-86. This would give you a set of 4 XOR's as shown in Fig. 1, just like the hardware chip 74-86. You could use as many as needed from these XOR gates in your design. Get back to ALL LIBRARIES and select switches for the inputs and Binary Probes as indicators of the outputs. Verify your design in the pre-Lab. During the Lab construct the circuit and verify its operations.
A digital circuit for adding two binary digits has two inputs: the two digits to be added; and two outputs: the units bit and the twos bit of the answer. (a circuit of this kind is called half adder.) By treating this as two circuits, each with a single output, use Karnaugh maps to obtain a Boolean expression for each circuit, and draw the corresponding circuit diagrams.
Assume 8-bit values for the following questions: a) find the equivalent unsigned binary number of 68 (decimal number). b) convert your result from a) to a hexadecimal number. c) find the two's complement binary number for -68. d) verify the binary sum of your results from a) and c) is 0. Find the status of the flags of N Z, C, and V.
Grey converters are often used in industrial circuits where the normal sequence of binary numbers may produce ambiguity during transition. This is elliminated with the Grey code, as only one bit changes, during a normal transition of sequential numbers. Show the logic required to convert a 10-bit binary number to Gray code and use that logic to convert the following to Gray code: a) 1010101010 b) 1111100000 c) 0000001110 d) 1111111111
Binary codes.Convert from Gray code to binary X1 = 10101111. From the result obtained, apply a complement to 2. Also, comment on an application of this code in particular.
Hi, i need to help to solve digital logic question that is about designin a-full subractor with two multiplexers (MUXs).
Answer n,o,p
2. Perform subtraction on the following unsigned binary number using 2's- complement of the subtrahend. a) 11011 - 11001 b) 11010 - 10101 c) 1011 - 11000 d) 101010 - 11011