1.2) (2 Points) Conductor spacings, types, and sizes do have an impact on the series impedance and shunt admittance. A. True B. False 1.3) (2 Points) Which of the following descriptions IS NOT correct for a lossless long transmission line? A. The theoretical maximum real power delivered occurs at the voltage angle difference across the line, 8 = 90° B. The characteristic impedance is a complex number C. Under the no-load situation, the magnitude of voltage at the receiving-end side is be higher than that at the sending-end side D. Under the surge impedance load, the magnitude of voltage at the receiving-end side equals to that at the sending-end side obo janú starb 1.4) (2 Points) Which of the following factors IS NOT a main factor which will impact the transmission line loadability?

1.2) (2 Points) Conductor spacings, types, and sizes do have an impact on the series impedance and shunt admittance. A. True B. False 1.3) (2 Points) Which of the following descriptions IS NOT correct for a lossless long transmission line? A. The theoretical maximum real power delivered occurs at the voltage angle difference across the line, 8 = 90° B. The characteristic impedance is a complex number C. Under the no-load situation, the magnitude of voltage at the receiving-end side is be higher than that at the sending-end side D. Under the surge impedance load, the magnitude of voltage at the receiving-end side equals to that at the sending-end side obo janú starb 1.4) (2 Points) Which of the following factors IS NOT a main factor which will impact the transmission line loadability?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.10MCQ: Transmission line conductance is usually neglected in power system studies. True False

See similar textbooks

Similar questions

Conductor spacings, types, and sizes do have an impact on the series impedance and shunt admittance. True False
Considering two parallel three-phase circuits that are close together, when calculating the equivalent series-impedance and shunt-admittance matrices, mutual inductive and capacitive couplings between the two circuits can be neglected. True False
Figure 4.34 shows double-circuit conductors' relative positions in segment I of transposition of a completely transposed three-phase overhead transmission line. The inductance is given by L=2107lnGMDGMRH/m/phase Where GMD=(DABeqDBCeqDACeq)1/3 With mean distances defined by equivalent spacings DABeq=(D12D12D12D12)1/4DBCeq=(D23D23D23D13)1/4DACeq=(D13D13D13)1/4 And GMR=[ (GMR)A(GMR)B(GMR)C ]1/3 with phase GMRs defined by (GMR)A=[ rD11 ]1/2;(GMR)B=[ rD22 ]1/2;(GMR)C=[ rD33 ]1/2 and r is the GMR of phase conductors. Now consider a 345-kV, three-phase, double-circuit line with phase-conductors GMR of 0.0588 ft and the horizontal conductor configuration shown in Figure 4.35. Determine the inductance per meter per phase in Henries (H). Calculate the inductance of just one circuit and then divide by 2 to obtain the inductance of the double circuit.
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
The conductor of a single-phase 60-Hz line is a solid round aluminum wire having a diameter of 0.412 cm. The conductor spacing is 3 m. Determine the inductance of the line in millinery’s per mile. How much of the inductance is due to internal flux linkages? Assume skin effect is negligible.
Answer all sub parts of question...
400Ω A k=0.9 600Ω B k=0.8 66Ω 600Ω
A 60 Hz, three-phase, transposed transmission line, is designed with three bobolink conductors per phase, in horizontal arrangement as shown in the figure below. Distance between consecutive phases is D = 6.2 m and distance among bundle conductors is h =0.5m. Each conductor has a radius of 18 mm and a GMR of 14.39mm. The per phase resistance is 1.677x10-5 2/m. r= 18 mm GMR= 14.39 mm a b h D D The per phase shunt admittance assuming zero conductance in µO/km is: О a., 5.4347 O b. j5.3316 О с /4.2266 O d. j4.0973 O e. 59630.2922 + j10.9770
In a short paragraph, explain the need to use bundled phase conductors in HV, EHV, and UHV 3-phase power transmission lines.
Question 3
Determine the capacitance and capacitive reactance per mile of this three-phase line shown below. The conductor is CAA Drake (it's radius is 0.0462 ft), the line length is about 175 miles and the normal operation voltage is 220kV at 60 Hz. Also consider that the conductors signaled as "AB" are 12 meter away from the earth.Determine the total capacitive reactance of the line considering the Earth Effect. Note: I think I should use this figure 5.9 but I just don't know how...
A 70 -mi, single-circuit, threc-phase linc composed of Ostrich conductors is arranged in flat horizontal spacing with 15ft betwecn adjacent conductors. The line delivers a load of 60MW at 230kV with 0.8 power-factor lagging. (a)Determine the series impedance and the shunt admittance of the line in per unit. Assume a wire temperature of 50° C.(b) Find the voltage, current, real and reactive power, and the power factor at thesending end. (c) What is the percent regulation of the line?