1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2. Complete any missing information on part 1&2 and in feature control 1 &2 (assume any tolerance). Explain your analysis ..not just numbers. Add all information needed for Gage 1 & 2 used to inspect Part 1&2 (show your calculations) 3. Part 1 Part 2 01.005+.005 Ø1.000 +.000 .005 000 Ø.500+ 000 005 .005 Ø.505 000 M Gage 1 Gage 2

1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2. Complete any missing information on part 1&2 and in feature control 1 &2 (assume any tolerance). Explain your analysis ..not just numbers. Add all information needed for Gage 1 & 2 used to inspect Part 1&2 (show your calculations) 3. Part 1 Part 2 01.005+.005 Ø1.000 +.000 .005 000 Ø.500+ 000 005 .005 Ø.505 000 M Gage 1 Gage 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative…
Need solution to both questions.
To which of the following geometric tolerance families does perpendicularly belong? Form Tolerance. Location tolerance. Profile tolerance. Orientation tolerance
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. Please refer to the attached image.
I need help matching the terms to the phrase it describes.
I need help answering this quick review pertaining to the print provided.
1. All orientation controls must have maximum material condition O a large tolerance zone O red text O datum features ?
Chapter 2: 6. Angular units of measurement are specified either in 7. Each feature must be or . Those dimensions specifically identified as reference, maximum, minimum, or stock do not require the application of a tolerance. and of the feature. 8. Dimensions must be selected and arranged to suite the function and mating relationship of a part and must not be subject to more than one 9. Unless otherwise specified, all tolerances and datum features apply for the full 10. Unless otherwise specified, all dimensions and tolerances are applicable at 11. What are the three types of direct tolerancing methods? 12. Where specifying decimal inch dimensions, a (temperature). Compensation may be made for measurements made at other temperatures. and is never placed before the decimal point for values less than one inch.
What type of geometric tolerances has no datum features? O Location O Runout O Profile O Form
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…