1. What is the code used for clockwise circular interpolation, if the tool is mounted in front of the job? (Reg. Number Ending with Even Numbers) 2. What is the comment can be used to specify the dimensions of the job in CNC programming? (Reg. Number Ending with Zero and Odd Numbers)

1. What is the code used for clockwise circular interpolation, if the tool is mounted in front of the job? (Reg. Number Ending with Even Numbers) 2. What is the comment can be used to specify the dimensions of the job in CNC programming? (Reg. Number Ending with Zero and Odd Numbers)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reaction turbine has guide vanes at an angle of 30° and the runner blades make an angle of 80° relative to the tangent at inlet. The blades width at the inlet is 4 of the outer diameter. The water does not have any tangential velocity at the outlet. The head is 25 m and the rotational speed of the runner is 16.67 rotations per second. The turbine efficiency is 88 %. Determine the turbine runner diameter at the inlet and the power developed. T
Write the commands to draw the figure shown below by using AutoCAD program?
Jensen Figure 6-71 Sketch 3 orthographic projections (i.e. top, front, right). Draw them on 10x10 cross section graph paper. - On each of the projections, label the inclined surface shown with its appropriate letter. - Identify if it is showing in first-angle projection or third-angle projection. b) a) K K Fig. 6-71 Sketching assignment 16.
Below is problem MV1 from the course pack. In an earlier assignment, you created a multiview drawing of this part. Model this part with SolidWorks, with each grid spacing equal to one inch. Create a SolidWorks drawing of this part, with Front, Top, and Right Views. Import dimensions from the SolidWorks part file, and place them on the drawing so that they can be easily read. Add a note that all dimensions are inches. Add your personalized title block that you created in Chapter 2 to this drawing. *Important: Save the drawing first as SolidWorks Drawing (filetype *.slddrw) and then as an eDrawing (filetype *.edrw)! You will upload the eDrawing in Blackboard, not the SolidWorks Drawing - the SolidWorks drawing is associated with the part file, I cannot open the sw drawing unless you also send the part file; however, l can open the eDrawing without the part file.
6. Write one block of code to perform the indicated operation. Assume the location is X2.0, Y2.0, and the depth is Z-1.5 for each operation. 1) Drill with dwell of 0.2 seconds 2) Peck drilling cycle with a 0.15" peck depth 3) Chip breaker with a 0.15" peck and full retract every 0.6" 4) RH tapping cycle for 14-16 NC thread; define a spindle speed and feed 5) Bore a hole with the tool being retracted manually
AutoCAD command prompts are grouped under TABS according to their command functions. Such groups are labelled as PANELS. Kindly Explore into details SEVEN PANELS.
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"
Pls heelpBlank is the time-honored tool for describing geometry
Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in3 Cyl. A DR = 62 in3 Cyl. B DE = 44 in3 Cyl. B DR = 41 in3
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
DO COMPLETELY AND TYPEWRITTEN FOR UPVOTE SKIP IF YOU ALREADY DID THIS OR ELSE DOWNVOTE