Answered: 1. Using the method of joints,…

1. Using the method of joints, calculate the force in each member of the trusses shown. State whether each member is in tension or compression. А B WANN E F P P C G

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: Calculate the force in each member of the loaded truss. Forces are positive if in tension, negative…

A: Tanθ = 3.6/3 θ = 50.16 Efy = 0 Ay + Cy = 0 Ay = - Cy EMA = 0 Cy X 6 + 2.7 X 3.6 = 0 Cy = - 1.62 kN…

Q: Answer the table below. The truss illustration and instruction is also below

A: Step 1: Step 2:Step 3:Step 4:

Q: eformation sustained by members CG, AF, 12 kips

A: Given:- 8 kips,12kips To find:- deformation sustained by members CG,AF,FG

Q: A simply supported planar truss is subjected to point loads at joint B and D as shown in Figure 2.…

A: Find the reaction of the truss calculate θ=tan-113.2710=52.99° and α=tan-113.275=69.35°consider ∑…

Q: By method of section

A: Determine the force in member JK, CJ and CD using method of section.

Q: The members of the truss shown below are made of steel (E = 200 GPa) with cross-sectional area of…

A: To determine the elongation of members of the given truss under the given loading, we can use the…

Q: For the truss shown in Figure 2.3a, determine the force in member BH if m = 5 m, n = 6 m, a = 83°,…

Q: Please solve this problem with a step by step guide so I can understand!

A: By considering the symmetry of the truss: AB = DEBC = CDAH = EFBH = DFBG = DGGH = GF

Q: E D H G 4 ft-4 ft- 3000 lb 1000 lb B K

Q: own below is 500 mm². 4. 3 m 3 m 3 m Determine the load P that will not (ceed a stress of 100 MPa in…

A: First find the reactions at the supports And then find the internal force in each member using…

Q: Design a square column to carry the working load of 1200 kN

A: given- a square column carrying load of 1200KN grade of steel=500 grade of concrete=M20

Q: Q2: Determine the force in members JK, JN, and CD. State if the members are in tension of…

A: A truss is given as shown in the figure above and it has been asked in the question to determine the…

Q: 3. The cantilever truss is loaded as shown in the figure; determine the force in members BD, CE and…

A: Consider the figure.

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A: Answer Let us first draw the free body diagram of forces acting on the given truss as shown below…

Q: The members of the truss shown below have a cross- sectional area of 10,000 mm2. Determine the…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: The FBD of the section is shown below:

Q: 1.20 Determine the smallest allowable cross-sectional areas of members CE, BE, and EF for the truss…

Q: : Consider the truss shown in the figure below, and answer the following questions. Figure is not to…

Question

1. Using the method of joints, calculate the force in each member of the trusses shown. State whether
each member is in tension or compression.
L
L
А
B
WANN
F
C
G

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introducing given data

VIEW

Step 2: Calculate reactions

VIEW

Step 3: Calculation for joint D

VIEW

Step 4: Calculation for joint A

VIEW

Step 5: Calculation for joints E & F

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Estimate the transverse tensile strength of the concrete in Problem 12.6.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel specimen in Figure 6.16.
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
What is the key element that influences the properties of iron?
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.