Answered: 1. Two slots have been cut in the plate… | bartleby

Related questions

Question

1. Two slots have been cut in the plate shown. The plate has been placed so that the slots fit two
fixed frictionless pins. Determine the force each pin exerts on the plate and the reaction at the
roller support.
50 N 70 mm
100 mm
100 mm
30°
A
|B
200 mm
C
100 mm
30°
50 N
180 mm
220 mm

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

. Asiacell ? 8:10 PM 38% O اسئلة الامتحان الثال. . . University of Technology Mechanical Engineering Department 2020-2021 Subject: Physics1 Class: First Year Division: power plant Timone hour Q1: The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T is 3 kN when 0 = 40°, determine the force P required on the lever and the corresponding tension T2 for this position. Assume that the surface under A is perfectly smooth. 650mm 100 mm T COO Q2: The force P is applied to (a) the 50 kg block and (b) the 150 kg block. For each case, determine the magnitude of P required to initiaite motion ? H = 0.40 50kg Pia) 4, = 0.12 150kg --YP(b)
1. Determine the forces the two people must apply in the new a and b directions shown such that a resultant force of 250N in the c direction is produced. Use the parallelogram method only. 250N 45° 30 B. 2. Determine the magnitude and direction of the resultant force, FA F= 400 N F= 200 N 90 150 VF = 300 N
1. Problem No. 1: A series of cables are connected to a ring at B and D, as shown in the figure. For this system: a) Draw the FBD of point D. b) Determine the force in cable DB and cable DE. A B 100 lb. 15° 80 lb. 45° E
2. Twoforces,oneofmagnitude2Nandoneofmagnitude3N,areappliedto the ring of a force table. The directions of both forces are unknown. Which of the following best describes the magnitude of the equilibrium force? Justify your answer.a. FE ≤ 5N b. 2N≤FE≤3N c. FE ≥ 3Nd. 1N≤FE≤5N e. FE ≤ 2N
B8
Two identical, side-by-side springs with spring constant 240 N/m support a 2.00 kg hanging box. Each spring supports the same weight. By how much is each spring stretched?
Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when 0 = 45° and P = 900 N. W = 700 N Ꮎ μs = 0.40 Mk = 0.30 P
8
Problem 6: If cable AB is subject to a tension of 700 N, determine the tension in cables AC and AD and the magnitude of the vertical force F. 3m 6 m- 6 m 3 m B 2 m- 2m 1.5 m
1. Given the vectors M = -10āx + 4ã, – 8ả, and Ñ = 8å, + 7ã, – 2ã,, find: a. A unit vector in the direction of -M + 2Ñ b. The magnitude of 5å, + N – 3M c. M||2Ñ|(M + N)
A2 Kg object moves on a track to the right at 10 m/s, and then reaches a circular depression. Assume the object stays on the track, and the radius of the track is 4 meters at the bottom of the circular depression. Also assume the bottom is 4 meters below the initial position of the object. There is no friction. 2 Kg 10 m/s When the object reaches the bottom of the circular depression, calculate the normal force that the track exerts on the object.
<→X CO|| 国 A 65-kg man is halfway up a 15-m ladder that is resting against a smooth, frictionless wall. If the ladder has negligible weight and it makes an angle of 55° with the ground, find the normal force from the wall acting on the ladder. Note: there is a force of friction acting on the foot of the ladder. A. Draw a FBD for the ladder [Select ] Diagram A Diagram B Diagram C Diagram D Diagram E B. Where is the best place to pick the pivot point in order to find the normal force from the wall acting on the ladder? [ Select] C. Find the normal force from the wall acting on the ladder [ Sclect] « Previous

SEE MORE QUESTIONS