1. Two generation units with following characteristics are connected to the grid. Find economic load dispatch (ELD) for Demand=400" using any arbitrary method. Assume that total grid loss is obtained as Pess=0.0005 P₁² +0,0002 P₂². F₁(P) = 400 + 5P₁ + 0.01 P₁² F₂ (P₂) = 600+4P₂ +0.015 2² MW MW 50 P300 < MV 25 << 200 MW

1. Two generation units with following characteristics are connected to the grid. Find economic load dispatch (ELD) for Demand=400" using any arbitrary method. Assume that total grid loss is obtained as Pess=0.0005 P₁² +0,0002 P₂². F₁(P) = 400 + 5P₁ + 0.01 P₁² F₂ (P₂) = 600+4P₂ +0.015 2² MW MW 50 P300 < MV 25 << 200 MW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The yearly load duration curve of a certain power station can be approximated as a straight line; the maximum and minimum loads being 40 MW and 10 MW respectively. To meet this load, three turbine generator units, two rated at 20 MW each and one at 10 MW are installed. Draw the load duration curve and determine: (i) Installed capacity (ii) Plant capacity factor (iii) kWh output per year (iv) Load factor.
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
Solve it fast plz
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
Can we improve a leading load pf using a synchronous condenser? Explain briefly your answerin one(1) sentence.
The steady-state voltage drop between the load and the sending end of the line seen in (Figure 1) is excessive Suppose that V-4950/0° V (rms). A capacitor is placed in parallel with the 192 kVA load and is adjusted until the steady-state voltage at the sending end of the line has the same magnitude as the voltage at the load end, that is, 4950 V (rms). The 192 kVA load is operating at a power factor of 0.8 lag. Part A Calculate the size of the capacitor in microfarads if the circuit is operating at 60 Hz. In selecting the capacitance, use the value that results in the lowest possible power loss in the line. Express your answer in microfarads to three significant figures. ▸ View Available Hint(s) Figure 1 of 1 202 1100 192 kVA 0.8 lag ΜΕ ΑΣΦ. 11 vec C= 22.8 Submit Previous Answers Incorrect; Try Again; 5 attempts remaining Provide Feedback ? F
B) Four regions of peak loads 5 MW, 7 MW, 8 MW and 10 MW are supplied by a generating station. The average annual load factor is 0.6 and the diversity factor at the station is 1.5. Calculate: (i) Annual energy supplied by the station (ii) The maximum demand on the station. (iii) If the installed capacity is greater than maximum demand by 20%, suggest the best number of units should be used to cover the load curve
Q)The question is that how kW is converted to kVA in complex form and how kV square is 2.4 for T1,T2,T3 can you plz explain it by seeing the solution
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
For the system as shown in the following figure, convert the components to same base voltage and apparent power, by choosing 100 kVA as the base kVA and 2000 V as the base voltage for the generators. Redraw the single line diagram with the new per unit values. 15 KVA 2000 V Z=j0.3 pu 25 KVA 2000 V Z=j0.15 pu G1 G2 35 KVA 2000/8000 V Z=j0.2 pu Z=30+j100 Z=60+j120 pu O pu leee 35 KVA 8000/2000 V Z=j0.3 pu 35 kVA 2000/8000 V Z=j0.25 pu G3 10 KVA 2000V Z=j0.35 pu M 30 KVA 2000 V
If the load draws a current of 2727 A, in phase, from a generator, which of the following statement is true? O A. The reactive power is flowing from generator to the load and the real power is flowing from the load to the generator. O B. Since the current is in phase with the generator voltage, both the real and reactive power is flowing from the generator to the load. O .Since the current is leading the generator, both the real and reactive power is flowing from the load to the generator. O D. The real power is flowing from generator to the load and the reactive power is flowing from the load to the generator. O E. None of the other choices are correct
What is the max load demand of the following feeders 4152 MW, 2.891 MW, 815.20 KW, 905.12 KWand 1.972 MW A) 10,735.32 KW B) 12,815.32 KW C) 10,571 MW D) 12.052 MW