1. The water in a 6-m-diameter, 2-m-high above-ground swimming pool is to be emptied by unplugging a 2-cm-diameter horizontal pipe attached to the bottom of the pool. Assuming the velocity in the pipe is 4h, where h is the height from the water surface to the bottom of the pool at an arbitrary fime t. Determine how long it will take to empty the swimming pool completely.

1. The water in a 6-m-diameter, 2-m-high above-ground swimming pool is to be emptied by unplugging a 2-cm-diameter horizontal pipe attached to the bottom of the pool. Assuming the velocity in the pipe is 4h, where h is the height from the water surface to the bottom of the pool at an arbitrary fime t. Determine how long it will take to empty the swimming pool completely.

Name: Homework 4 Mass and Energy Conservation1. The water in a 6-m-diameter
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Homework 4 Mass and Energy Conservation1. The water in a 6-m-diameter, 2-m-high above-ground swimming pool is to be emptied byunplugging a 2-cm-diameter horizontal pipe attached to the bottom of the pool. Assuming thevelocity in the pipe is 4, where

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A pipe with varying cross-sectional areas is set up vertically as shown in the drawing. Water enters the pipe from the top wider end at a speed of 300 cm/s. Calculate (a) the mass flow rate of water (the amount of mass entering/exiting the piper every second) and (b) the water pressure at the bottom narrower end section of the piper. (Density of water is p = 1000 kg/m2 1.00 g/cm')) P 1.20x10 Pa 10.0 cm h=4.00 m 2.50 cm2 P= ?
(4) A water hose connected to a nozzle is used to fill a 10 L container. The internal diameter of the hose is 2 cm and the nozzle exit has an inner diameter of 1.7 cm. It takes 30 s to fill up the container. If the inlet pressure is 2 atm and the nozzle exit is 0.8 m above the hosea. What is the velocity (m/s) of water at the outlet stream and at the inlet stream?b. What is the water pressure (atm) at the outlet stream c. What is the mass flow rate of water (kg/s)?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i. Determine Delta Z (Z2 - Z1) in ft. ii. What is the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s. iii. What is the mass flow rate of the water in lbm/s?
A plane with a jet engine is flying at 790 mph into a 80 mph headwind. The area of the jet engine inlet is 2.5 square feet. Determine the volumetric flow rate of air into the jet engine inlet in cubic feet/second.
2. 80 m below the free surface of a large water reservoir that can supply water at a rate of 2200 kg/s steadily. If the mechanical power output of the turbine is 1400 kW, determine the turbine efficiency. Neglect losses in the pipes. The gravitational acceleration is g-9.81m/s². Generator h = 80 m Turbine m 2200 kg/s
Water flows through a garden hose at a rate of 1 l/s. The upstream diameter of the hose is 2.5 cm, and the nozzle outlet has a diameter of 1 cm. Determine the upstream pressure (gage pressure).
A large, open-topped water tank is being filled from above by a 1.0-cm-diameter hose. The water in the hose has a uniform speed of 11 cm/s. Meanwhile, the tank springs a leak at the bottom. The hole has a diameter of 0.70 cm. Determine the equilibrium level heq of the water in the tank, O measured relative to the bottom, if water continues flowing into the tank at the same rate. heq 1.26 X10-3 Incorrect m
If you have a flat tire and need to pump up the tire on your car with a hand pump, what force do you have to apply to the pump handle? Assume the air pressure in your tire will be 20 lb/in2, that is 1.1 KPa (138,0000 N/m2). Let the air pump have a cross-section that is 5 cm in diameter. It depends on the weight of the car. About 270 N when the tire is full, not much when you start pumping on the empty tire. About 270 N for as long as it takes from the beginning. Just a few newtons until you are satisfied with how full the tire is because of the hand pump.
A 100-mm diameter jet of water is discharging from a nozzle into the air at a velocity of 36 m/s. the nozzle is inclined at an angle of 25 degrees with horizontal. neglecting air ressistance, determine: 1. the elevation of the highest point with respect to a datum at the tip of nozzle. 2. the area of the jet at the highest point of the stream.
(a) If it takes 2.35 min to fill a 20.5 L bucket with water flowing from a garden hose of diameter 3.30 cm, determine the speed at which water is traveling through the hose. m/s(b) If a nozzle with a diameter four-fifths the diameter of the hose is attached to the hose, determine the speed of the water leaving the nozzle. m/s
60 degree F water flows through a horizontal turbine. The water speeds at the turbine inlet and the turbine outlet are identical. The water gage pressure at the turbine inlet is 46.4 psi while that at the outlet is 12.2 psi. Assume water frictional losses through the turbine are negligible. Deterimine the shaft work rate in ft*lb per slug of water passing through the turbine. Answer with a positive number if mechanical energy goes into the water and a negative number if mechanical energy comes out of the water as it passes through the turbine.
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. a. Assuming that the large open reservoir is open to the atmosphere as well, what is the mechanical energy balance eq for the system? b. What is the Reynolds number for the flow ?