1. The secondary of a three-phase transformer is shown in Fig. (1). The RMS secondary phase voltage is 45V. i Draw the waveforms of load voltage, i. diode (D1) current, and diode (D1) voltage. Calculate the average output voltage. il. Calculate the value of R if the load power il. is 100w. iv. Determine the diode ratings. (S = start F= finish) Vo Fig. (1)

1. The secondary of a three-phase transformer is shown in Fig. (1). The RMS secondary phase voltage is 45V. i Draw the waveforms of load voltage, i. diode (D1) current, and diode (D1) voltage. Calculate the average output voltage. il. Calculate the value of R if the load power il. is 100w. iv. Determine the diode ratings. (S = start F= finish) Vo Fig. (1)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A semiconductor diode having ideal forward and reverse characteristics is used in a half-wave recti- fier circuit supplying a resistive load of 1000 Ω. If the r.m.s. value of the sinusoidal supply voltage is 250 V, determine (i) the r.m.s. diode current
Please help solve this problems
Ce301 q5
9. The following circuit is a voltage limiting circuit. The diode has an offset voltage of 0.7 V. (a) Determine the maximum & minimum voltages for Vout(t) for both the positive and negative cycles of Vin(t) (b) Calculate the maximum current flow during the positive cycle of Vin(t) (c) Sketch the waveforms for Vin(t) and Vout(t) for 2 cycles, indicate on the waveform the period, maximum and minimum values. (d) Sketch the output waveform Vout(t) if Vin(t) is set to 10 V pp. Vin(t) Vp = 12 V 50 Hz 470 Ω 5 V Vout(t)
The 3-phase half-wave diode rectifier feeds a load consisting of a 50-ohm resistor. The sinusoidal sources in the input of the rectifier are wye-connected and phase-to-phase rms voltage is 380 volts. Calculate the power (in watts) absorbed by the load. Assume the diode is ideal. a. 680.36 b. 2267.90 C. 4082.20 d. 1700.90 e. 1360.70
(b) If such a circuit is to be used to supply an average of 10 V across the load, calculate the turns ratio of the transformer required. The input mains voltage is 240 V rms at 50 Hz. You may assume ideal diodes in your analysis. Note again that there is to be no smoothing of the load voltage.
Hey, I need the answers to these questions. It's urgent.
Three Phase Uncontrolled Half Wave Rectifiers find the value of Voltage and Currents (output de and Root Mean Square) with all the proved, then sketch the curve from 0-2 on these axes (vs, vo, ia, ib, ic, io) explain its operation.
part F please
What voltage is boosted at the output of a multiplier. a) average b) rms c) peak d) instantaneous Which assumption is not used in the analysis of multipliers? a) a capacitor will not discharge b) start with the cycle of the source that will forward bias the nearest diode c) the output will always be multiplied d) a single diode is forward biased at a time A voltage multiplier a) multiplies the output voltage b) has very high voltage and low current c) can employ inductors d) may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations at a) the input and output b) the load c) source d) in the environment Between a lower percent regulation and a higher one, which is better? a) lower b) higher
Draw the circuit using only ideal diodes, resistors and voltage sources to obtain the Vo-Vi relationship whose characteristic is given below (the values shown on the characteristic are slope values).
The input to a 3-phase full-wave rectifier is 60 Hz AC voltage. If the voltage drop across diodes is 0 V, The RMS voltage at the load would be: O A. None of the other choices are correct O B. Cannot tell until we have more information O C. Lower than the RMS voltage at the input O D. Higher than the RMS voltage at the input O E. The same as the RMS voltage at the input