Short answers are ok. D4 D1+RL+1.2KVsD3D29V sin(2n 50 t)Verify the amplitude and frequency of the output waveform on the load resistor, RL.Peak voltage:Waveform period:Frequency1.a) Which diode(s) is/are on during the positive and negative cycles of Vs?1.b) Vs frequency is 50 Hz. Why the v frequency is 100 Hz?1.c) Calculate the average power dissipated on all four rectifier diodes(assume that each diode is ON for exactly one half cycle of Vs for simplicity).1.d) How much power would have been dissipated on the diodes in total, if thesame output waveform was obtained using a full-wave rectifier with a center-tapped transformer?

Answered: Image /qna-images/answer/3628cf5b-f8d6-4ce6-82c6-54dc70f50840.jpg

D4 D1 + RL + 1.2K Vs(N D3 Y D2 9V sin(27 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RL. Peak voltage: Waveform period: Frequency 1.a) Which diode(s) is/are on during the positive and negative cycles of Vs? 1.b) Vs frequency is 50 Hz. Why the v frequency is 100 Hz?

D4 D1 + RL + 1.2K Vs(N D3 Y D2 9V sin(27 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RL. Peak voltage: Waveform period: Frequency 1.a) Which diode(s) is/are on during the positive and negative cycles of Vs? 1.b) Vs frequency is 50 Hz. Why the v frequency is 100 Hz?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
What is the difference between a diode and rectifier?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
b. using the conventional current flow, where is the direction of the current during the positive cycle at node A.c. Where is the direction of the current during positive cycle at node B.d. draw the output waveform(use the idea diode model)
Consider the diode circuit shown below. If Vs is a sinewave with a peak amplitude of 12 Volts at 60Hz, and diodes D1 & D2 are considered ideal, sketch the appearance of the waveform at node voltage Vout . Sketch the appearance of the waveform at Vout .
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
Four diodes and one Zener diode are connected to form the circuit below. a) Describe how a single diode behaves when forward biased. 5) draw the output as the input changes from -12 V to +12 V. Assume that all diodes can be represented by a constant-voltage of 0.6 V (in forward bias) and the Zener diode has a breakdown voltage of 6.8 V. d) What is the function of the circuit? Suggest a proper application. I kN Da Dr
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
Given the clamper circuit below, assume that the value of R and C are large enough so the voltage across the capacitor does not change significantly during the interval of time. a. Using the simplified diode model, simulate the action of the circuit when the diode is in forward and reverse bias condition and measure its output voltage. b. Draw the output waveform of the circuit. VIN +8V ER 1.3V. -8V
ill rate thank you