1.The schematic shown below represents high and low values of which of the followingthermal properties of materials?A. Diffusivity B. Conductivity C. Thermal Expansion D. Heat capacity2.Which one of the following does not represent one of the six families of materials?A. Metals B. Ceramics C. Woods D. Hybrids3.Which one of the following is not a typical property of a glass?A. High hardness B. Electrically Insulating C. Transparency D. High Toughness4.Which of the following material properties is most appropriate for describing the stiffnessof a material?A. Young's Modulus B. Yield Strength C. Fracture Toughness D. Fatigue Limit5.The failure of the aircraft wing shown below, when loaded to its design stress, suggeststhe following about the material it is manufactured fromA. Not stiff enough B. Too low a yield strength C. Too low a fracture toughness D. Too higha ductility

As per bartleby guidelines we are allowed to solve only 1st 3 MCQ if multiple MCQs are posted. So…

1. The schematic shown below represents high and low values of which of the following thermal properties of materials? A. Diffusivity B. Conductivity C. Thermal Expansion D. Heat capacity 2. Which one of the following does not represent one of the six families of materials? A. Metals B. Ceramics C. Woods D. Hybrids 3. Which one of the following is not a typical property of a glass? A. High hardness B. Electrically Insulating C. Transparency D. High Toughness

1. The schematic shown below represents high and low values of which of the following thermal properties of materials? A. Diffusivity B. Conductivity C. Thermal Expansion D. Heat capacity 2. Which one of the following does not represent one of the six families of materials? A. Metals B. Ceramics C. Woods D. Hybrids 3. Which one of the following is not a typical property of a glass? A. High hardness B. Electrically Insulating C. Transparency D. High Toughness

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2: A fiberglass composite consists of a matrix of vinyl ester and reinforcing fibers of E-glass. The volume fraction of E-glass is 30%. The density of the vinyl estiser 0.882 g/cm³, and its modulus of elasticity is 3.6 GPa. The density of E-glass is 2.6 g/cm³, and its modulus of elasticity is 76 GPa. A section of composite 1 cm by 25 cm by 2 m is fabricated with the E-glass fibers running longitudinally in the 2000 mm direction. Determine: (a) The masses of vinyl ester and E-glass fibers. (b) The density of the composite. (c) The composite modulus of elasticity in the longitudinal and the perpendicular directions of the glass fibers. (d) If the tensile strength of the glass fibers, is 1 GPA and the tensile strength of the epoxy matrix is 60 MPa, find the tensile strength of the composite in the longitudinal direction.
Plastics may exhibit a change in properties as they age, particularly when subjected to elevated temperatures. Material properties such as tensile strength will increase with an increasing temperature as a function of increasing time. True or false.
Question 5: The graph below gives a plot of force versus total sample length in a tensile test of a polymer. The sample is cylindrical, with an initial diameter of 1 cm and an initial length of 10 cm. From the data below, calculate the modulus, yield stress, yield strain, tensile strength, and % elongation. 1200 800 10 12 13 14 15 Lensth (cm) Force (N)
The properties of materials can be classified into the following categories: Mechanical Physical Thermal Electrical Magnetic Describe each category, include two specific properties in the description and say why those properties are of interest to a design engineer.
Q2/ Determine the weight and number average molecular weights as well as degree of polymerization for the polypropylene materials. Number Range of Molecular weight in gram/mol and weight fractions X₁ W₁ 8000- 16000 0.05 0.02 16000- 24000 0.16 0.1 24000- 32000 0.24 0.2 32000- 40000 0.28 0.3 40000- 48000 0.20 0.27 48000- 56000 0.07 0.11
Question 2 Figure 2 shows the dependence of fatigue strength on testing cycles (S-N curve) of an acetal polymer. 60 50 40 30 20 10 104 105 106 107 108 Number of cycles to failure Figure 2 The S-N fatigue curve for an acetal polymer a. What is the fatigue strength, or maximum stress amplitude, at one million cycles of loading? b. An acetal polymer 30-cm-long bar with a diameter of 20 mm is designed to survive one million cycles of loading, what is the maximum allowable axial load that can be applied on one end of the bar? Magnitude of stress Reversal, MPa
The core concept of materials science relies on the inter-dependent relationship among the structure, properties, performance, and processing which is represented in a tetrahedron known as Materials Science Tetrahedron (MST), shown in FIGURE Q1a. Using the concept of Materials Science Tetrahedron, answer the following questions pertaining to the choice of materials for engine blocks. An example of an engine block is shown in FIGURE Q1b. Performance Processing Structure Properties Figure Q1A Figure Q1B You are to justify for the choice of material selected for an engine block. Include at least FOUR (4) factors in your discussion.
2 - What is the appropriate device for diagnosing each of the following and why? A- The aluminum plate is coated with a nano-solution. b- A colloidal sample containing nano-solutions. C- Study of the microstructure of the surface of a sample of iron. D- Study the phases and components of the organic powder.
Which of the following is correct regarding the degree of crystallinity of semi-crystalline polymers? Semi-crystalline polymers are heat treated to increase the crystallinity and improve polymer strength The tendency of a polymer to crystallize increases with increasing molecular weight Degree of crystallinity and tendency to creep have an inverse relationship Increasing the degree of crystallinity generally increases polymer strength, elastic modulus and ductility in semi-crystalline polymers
An unknown polymer sample was found to have the following molecular weight distribution: Molecular weight range Xi Wi 8,000 – 20,000 0.05 0.02 20,000 – 32,000 0.15 0.08 32,000 – 44,000 0.21 0.17 44,000 – 56,000 0.28 0.29 56,000 – 68,000 0.18 0.23 68,000 – 80,000 0.10 0.16 80,000 - 92,000 0.03 0.05 What would the weight average molecular weight of the sample be if, we had filtered the monomer mixture with a 44 kDa dialysis tubing before preparation? (Hint: a dialysis tubing of a known molecular weight, only keeps molecules larger than that size)
3. Metals have ............ thermal conductivity value compared to polymers. a. Low b. Very low c. High d. Medium 4. Determine the length of a copper wire that has a cross - sectional area as 8.1 mm2. The resistance and the electrical resistivity of the copper wire are 14 and 1.79 x 10-6 m. The length of a copper wire (in meters)