1.) The casting shown in the following figure has a mass of 1.75 Mg. It is suspended in a vertical position, is initially at rest, and is given an upward speed of 500 mm/s in 0.25 s using a crane and hook "H". Determine the tension in cables AC and AB during this time interval if the acceleration of the casting is constant. H Ans. TAC = TAB = 11.93 KN

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: The elevation and tilt angle of table AB are controlled by an operator's hand at point D. The table…

A: Freebody diagram of Table AB:Freebody diagram of the member DCB:

Q: Cork k =.045 also all are 300 K values ... please resolve

A:

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: From the figure shown. To determine: a) Piston force BC b) Piston force FE c) Pin force G and J d)…

A: Consider the free body diagram of bucket is shown below, Taking moment about point J, ∑MJ=020000…

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Q: Bar AB has an angular velocity AB = 7 rad/s Part A Determine the velocity of the sider block Cat the…

A: Given:BC = 350 mmAB = 500 mm or 0.5 m/s90° - 60° = 30°45°7 rad/sRequired:VC ( velocity of slider…

Q: I need these three parts answered, if you are unable to answer all three parts please leave it for…

A: 4.The number 81073 denotes the CAGE no. as shown in the print. The CAGE code indicates Commercial…

Q: 5. I went for a 2 mile bike ride. With the given information below, how many times did I pedal my…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.