1. Neglecting friction and the weights of the members, compute the magnitudes and directions of the pin reaction at And C for the folding table shown30 kN/mA. RA = 15.12 kN and R: = 32.8 kNB. Ra = 44.69 kN and R = 43.01 kNC. RA = 13.3 kN and Rc = -5.4 kND. Ra = 410.8 kN and R = 415.5 kNE. None of the above (state your answer)10 kN/m%3D1.2 m0.8 m0.8 m

The FBD of the table is shown below: Taking equilibrium equation:

1. Neglecting friction and the weights of the members, compute the magnitudes and directions of the pin reaction at A nd C for the folding table shown 30 kN/m A. RA = 15.12 kN and Re = 32.8 kN B. RA = 44.69 kN and R: = 43.01 kN C. R = 13.3 kN and Re = -5.4 kN D. RA = 410.8 kN and Re = 415.5 kN 10 kN/m E. None of the above (state your answer) 1.2 m 0.8 m 08 m

1. Neglecting friction and the weights of the members, compute the magnitudes and directions of the pin reaction at A nd C for the folding table shown 30 kN/m A. RA = 15.12 kN and Re = 32.8 kN B. RA = 44.69 kN and R: = 43.01 kN C. R = 13.3 kN and Re = -5.4 kN D. RA = 410.8 kN and Re = 415.5 kN 10 kN/m E. None of the above (state your answer) 1.2 m 0.8 m 08 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: Given: a = 0.4 m b=0.1 m F₁ = 800 kN F₂ = 915 kN M₁ = 400 kNm •A •B 0.7 m 1 m 1) Find the shear force at Point B, VB: 2) Find the bending moment at Point B, MB:
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions are provided. MB = 148 kN-m Mc = 67 kN-m Ay = 17.92 kN (down) Dy = 17.92 kN (up) 5 m O 74.7 kN-m O 65.0 kN-m O 89.6 kN-m O 56.7 kN-m O 83.1 kN-m MB B 4 m Mc 3 m D X
27 - Support reactions will be found in the gerber beam whose loading condition is given in the figure. A is the fixed joint, the G point is the intermediate joint, and the B and C supports are the sliding joint. Loads on the beam P1 = 24 kN, P2 = 2 kN, q= 4 kN ⁄ m, beam dimensions a = 4 m, b = 2 m. Accordingly, Bx = ? a) 6B) 4C) 10.5D) None.E) 0
A force of 521 kN is applied at joint B to a system of two-pinned joined bars shown in the figure. Determine the required cross-sectional area of the bar BC if the allowable stresses are 175 MPa in tension and 74 MPa in compression. 521 kN B 1.5 mt 1.5 m 3.0 m 3.0 m
Show step by step
Set-up the overall stiffness matrix necessary to compute the nodal displacements at B and C. Compute the member forces of AB and BC and then determine the reactions at A and C. El=constant. 30 KN/m 6 m. В 4 m
Calculate the reactions of supports for beam below using forced method of analysis.
2. Determine the reaction at the supports using E= 70 GPa and I = 1,300,000,000 mm^4. Use excel spreadsheet to determine the values of the unknowns. Draw the FBD of the beam with the calculated values of the support reactions. 150 kN 35 kN/m 4.0 m 2.0 m 2.0 m
Question: Given: a = 0.4 m b=0.1 m F₁ = 800 kN F₂ = 915 kN M₁ = 400 kNm •A 0.7 m 1 m 1) Find the shear force at Point B, VB: B M, 2) Find the bending moment at Point B, MB:
Q2/ Determine the reactions at the supports. Assume B is hinge connected. El is constant .Use Method of Slope Deflcction Equation.(. (P in kN/m)
Question: Given: a = 0.4 m b = 0.1 m F₁ = 800 Kn F₂ = 912 kN M₁ = 400 kNm •A •В 0.7 m 1 m 1) Find the shear force at Point B, VB: 2) Find the bending moment at Point B, MB: