What is the Maximum moment in kN-m.Given: w = 42, a = 4, b = 4, and c = 3.%3Dw kN/mamb mRpRA

Answered: Image /qna-images/answer/b4d8286b-3c46-441c-8700-94c9cf0b10d4.jpg

Answered: What is the Maximum moment in kN-m.…

Engineering

Civil Engineering

What is the Maximum moment in kN-m. Given: w = 42, a = 4, b = 4, and c = 3. %3D %3D w kN/m am b m Rp RA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
Which of the following is the nearest value for the force at member BC? a. 5kN tension b. 1.6 kN tension c. 1.6 kN compression d. 5 kN compression
There is a horizontal external force P = 4kN applied on point B. The axial rigidity EA of all truss members is constant. Use the Force Method to determine the Horizontal Displacement of point B (VBH). B C P=4kN A 4m 3m
QUESTION 1) The cross sectional Е, A, Е, А, areas of the KM and MR intervals are A1 = 400 mm? and A2 respectively. Both sections are made = 200 mm², from the same material that has elastic L. M N R K modulus ofE = 200 GPa. If the gap in figure is 8-5mm and the axial forces are Pi = 120 kN and P2 1m 2m 2m 1m = 80 kN; a) Calculate the support reactions. b) Draw the axial force diagram.
Determine the variation in the width w as a function of x for the cantilevered beam that supports a concentrated force P at its end so that it has a maximum bending stress sallow throughout its length. The beam has aconstant thickness t.
The three bars have a weight of WA = 20 lb, Wâ = 40 Ib, and Wc = 2. 60 Ib respectively. If the coefficients of static friction at the surfaces of contact are as shown, determine the smallest horizontal force P needed to move block A. C"CB = 0.5 17 BHBA = 0.3 15 A HAD = 0.2 D
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150×10° N/m². The cross sectional area of each member is 0.01 m?. Forces P, and P2 are acting as shown, Wall (e= 40°, P;= 8 kN) 2 (a) (b) 3 409 (c) 30 P1 P= 2kN 4m FIGURE Q2 а. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by performing complete calculations to justify your recommendation.
3. A planar truss is constructed of steel members, all of which have a cross-sectional area of 3000 mm?. Determine the nodal displacements, reactions and element stresses. G 2 m B D 2m 50 kN 460 kN
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft
solve fast