1. Member B is subjected to a compressive force 600 lb of 600 lb. If A and B are both made of wood and are 1.5 in. thick, a) determine to the nearest 1/8 in. the smallest dimension a of the support so that the average shear stress along the blue line does not exceed Tallow = 50 psi, and b) determine to the nearest 1/8 in the smallest dimension b so B. that the average bearing stress does not exceed Op = 80 psi. Neglect friction.

1. Member B is subjected to a compressive force 600 lb of 600 lb. If A and B are both made of wood and are 1.5 in. thick, a) determine to the nearest 1/8 in. the smallest dimension a of the support so that the average shear stress along the blue line does not exceed Tallow = 50 psi, and b) determine to the nearest 1/8 in the smallest dimension b so B. that the average bearing stress does not exceed Op = 80 psi. Neglect friction.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the O.63-in .-diameter pin at A, and the 0.3-in.-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5012 Ib. Round off the final answer to two decimal places. 0007 P.png ... 70 4 in 3.5 in. 30 0.5-in dia. Detail at A
The allowable shear stress is Tallow = 855 psi. The supports at A and B are smooth. 3 ft 6 ft- 3 ft 2 in. 6 in. I in. 2 in. I in. Part A Determine the largest intensity w of the distributed load that the member can support. Express your answer to three significant figures.
B 1 boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi AB cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places 70° 30° 12 ft C Р 4 in. 3.5 in. Detail at A H 0.5-in. dia.
Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded together as shown. Assume a = 4.0 in. For a load of P = 75 kips, determine (a) the normal stress that acts perpendicular to the weld and (b) the magnitude of the shear stress that acts parallel to the weld. Answer: O= P T = 1 i 1 ksi ksi b P
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 14 mm2. For a uniformly distributed load of w = 4.1 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.35 m. A (1) (2) a L. Answer: a = i m
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 15 mm². For a uniformly distributed load of w = 3.2 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.60 m. A (1) B Answer: a = i L a D (2) m
Two horizontal 6.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 1.8 in.. 60° 45% P P 0.5 in. 1.8 in. С Determine the average bearing stress at C in member BC. The average bearing stress at C in member BC is ksi.
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
The cantilever beam AB will be installed so that the 60-mm side forms an angle β between 0 and 90° with the vertical. The 660-N vertical force P is applied at the center of the free end of the beam. Determine the value of β for which the normal stress at point a is a maximum and the corresponding value of that stress. (Round the final answer to two decimal places.)
The timber member has a cross-sectional area of 1850 mm? and its modulus of elasticity is 12 GPa. What is the normal stress in member AB? 40 kN 35 kN 20 kN D A B +1.5 m→ - 3 m - - 3 m · Select one: O a. 8.11 MPa b. 10.81 MPa с. 13.51 MPа d. 21.62 MPa
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8