/Answer( any five) of the following1. List the seven types of failure2.Define die penetrant test3.Suggest N.D.T.test for an internal defects of metal4 Define pn juction diode5. What is the behaviour of smart material (Ti-Br) alloy6. What is the effect of plasticisers that added to polymer

Answered: 1. List the seven types of failure…

Engineering

Mechanical Engineering

1. List the seven types of failure 2.Define die penetrant test 3.Suggest N.D.T.test for an internal defects of metal

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q\ What is the best material that has a very good Young modulus and low density?
When a failure data set for a ceramic material processed in a certain facility is analyzed, it is found that the characteristic strength is 327 MPa and the Weibull modulus is 8.75. A nominally identical batch of material processed in a different facility is also tested and found to have essentially the same characteristic strength, but the Weibull modulus is 6.25. At what stress level is the probability of failure equal to 50% for each set of material? What initial conclusion might you draw about the quality control procedures at the two facilities?
Stuck need help! Problem is attached. please view attachment before answering. Really struggling with this concept. Please show all work so I can better understand ! Thank you so much.
Design an experiment to determine the minimum thickness of a soda bottle required to hold a specific beverage without failure, from production line to consumer use
I need the answer as soon as possible
What happens if you add a small imperfection to a system that has a saddle-node bifurcation?
A cylindrical rod having a diameter of 10.0 mm is to be deformed using a tensile load of 20,500 N. It must not experience either plastic deformation or a diameter reduction of more than 4 x 10-³mm. Referring to the materials listed below, which are/is possible candidates? Justify your choice(s). Material Magnesium alloy Brass alloy Steel alloy Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson's Ration 200 0.35 0.34 0.30 45 101 207 300 400
i need the answer quickly
Polymeric materials are liable to creep at room temperature, stress and time of loading, which one of the following statements is correct? a. the longer the time, the creep strain increase. b. The higher the temperature, the higher the creep limit. c. Reduce the stress increases the strain. d. Increase the temperature increases the creep strain.
No wrong answer please , i could downvote The piece of suture is tested for its stress relaxation properties after cutting 3 cm long sample with a diameter of 1mm. The initial force recorded after stretching 0.1 cm between grips was 5 Newtons. Assume the suture material behave as if it has one relaxation time. The gage length was 1 cm. a. Calculate the initial stress. b. Calculate the initial strain. c. Calculate the modulus of elasticity of the suture if the initial stretching can be considered as linear and elastic. d. Calculate the relaxation time if the force recorded after 10 hours is 4 Newtons.
Manufacturing 1-V2 (1) - Compatibility Mode Saved - O Search Review View Help E E - E EE >T T I AaBbCcDd AaBbCcDd AaBbC AaBbCcl Aa 1 Normal 1 No Spac. Heading 1 Heading 2 Title Paragraph Styles 7. Assuming that the density of steel and aluminium are 7.9 and 2.7 g/cm, respectively, which material has the best strength-to-weight ratio? (Hint: the strength-to-weight ratio is called specific strength, equal to yield strength divided by density).
A polymer has creep behaviour that can be represented as a power law equation: e = 0 (Jo + Jit") where J, is 0.5 GPa1, J1 is 0.45 GPa's 0.3 and n is 0.3 (with t in seconds). A component of this material has the following applied stress history: There is no stress before t = 0 A positive (tensile) stress of 8 MPa is applied from t = 0 for 4 hours From t = 4 hours to 6 hours, the stress is compressive stress of 2 MPa The stress is then removed. What will the strain in the material be at t = 9 hours? Enter your value as a number to 4 decimal places. You have a 2% error margin with this.