1. In this scenario, assume you are working on the link layer protocol using Stop-and-Wait ARQ data connection with a bandwidth of 500 Mbps to an oversea station in Taiwan. Assuming the station in Taiwan is 3057 km from the local station in Kuala Lumpur and the propagation speed is c = 2.2 x 10² m/s, answer the following: a) Calculate the bandwidth-delay product for communication between the two stations. b) Identify the utilization percentage of the link if the system data frames are 800 bits in length. c) Solve for the utilization percentage of the link if we have a protocol that can send up to 8 frames before stopping and worrying about the acknowledgments.

1. In this scenario, assume you are working on the link layer protocol using Stop-and-Wait ARQ data connection with a bandwidth of 500 Mbps to an oversea station in Taiwan. Assuming the station in Taiwan is 3057 km from the local station in Kuala Lumpur and the propagation speed is c = 2.2 x 10² m/s, answer the following: a) Calculate the bandwidth-delay product for communication between the two stations. b) Identify the utilization percentage of the link if the system data frames are 800 bits in length. c) Solve for the utilization percentage of the link if we have a protocol that can send up to 8 frames before stopping and worrying about the acknowledgments.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches. (c) Same as (a), but assume the switch implements “cut- through" switching; it is able to begin retransmitting the packet after the first 200 bits have been received.
Suppose we have a reservation system with 50 users, frame transmission time of 0.6 sec, v = 0.3. (a) What is the effective frame transmission time? (b) What is the efficiency/throughput if all stations are transmitting? (c) What is the efficiency/throughput if a minislot can reserve up to 7 frames?
Computer Science Two flows are transmitting at a constant rate of 4Mbps and 8Mbps and compete for service at a 10Mbps link. If the link adopts an RED policy, what is the expected drop probability for each flow?
In a CSMA/CD network with a data rate of 10 Mbps, the minimum frame size is found to be 512 bits over maximum cable length 2500 m. what should be the maximum cable length if we increase the data rate to 100 Mbps?
?
5 points Find the latency of Token Ring (in bits) where data rate of link is 20 Mbps and 40 stations separated by 100 meters and bit delay at each station is 1 bit. (Assume propagation speed as 2x105 m/sec)
4) Design a statistical multiplexer. Traffic parameters: arrival rate = 1,000 packets/sec & average packet length = 1000 bits/ packet. QoS parameters: E[T]=lms & PB=104. Find the link capacity in Mb/s and system size needed to achieve these QoS specifications.
Assume a 10Mbps Ethernet has two nodes, A and B, connected by a 360m cable with threerepeaters in between, and they each have one frame of 1,024 bits to send to each other. Further assumethat the signal propagation speed across the cable is 2*10^8 m/sec, CSMA/CD uses back-off intervals ofmultiples of 512 bits, and each repeater will insert a store-and-forward delay equivalent to 20-bittransmission time. At time t=0, both A and B attempt to transmit. After the first collision, A draws K = 0and B draws K = 1 in the exponential back-off protocol after sending the 48bits jam signal. a. What is the one-way propagation delay (including all repeater delays) between A and B inseconds? At what time is A's packet completely delivered at B? b. Now suppose that only A has a packet to send and that the repeaters are replaced with switches.Suppose that each switch has an 8-bit processing delay in addition to a store-and-forward delay.At what time, in seconds, is A's packet delivered at B?
We define data link layer communication efficiency as the ratio between a packet transmission time and the sum of the the packet transmission time-and twice of its, propagation time. A channel has a bit rate of 10 kbps and a propagation delay of 10,000 micro-second. For what range of frame sizes (in number of bit) does stop-and-wait give an efficiency of at most 60%?
Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches. (c) Same as (a), but assume the switch implements “cut- through" switching; it is able to begin retransmitting the packet after the first 200 bits have been received.
4
If 'B’ is the network bandwidth, 'L’is the cable length and 'C' is the speed of the signal propagation, 'e' is the number of contention slots per frame and 'F' is the frame length, then channel efficiency 'i' is: