Suppose you are designing a sliding window GBN protocol for a 5 Mbps point to point link, which has a one way propagation delay of 3.3 sec. Assuming that each frame (segment) carries 574 byte of data. What is the minimum number of bits do you need for the sequence number? Assume error free link. Answer:

Suppose you are designing a sliding window GBN protocol for a 5 Mbps point to point link, which has a one way propagation delay of 3.3 sec. Assuming that each frame (segment) carries 574 byte of data. What is the minimum number of bits do you need for the sequence number? Assume error free link. Answer:

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 19VE

See similar textbooks

Similar questions

Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During each time slot 8 bits are sent. What is the shortest time possible (in seconds) to transmit a 1 Mbyte file over the given link?
Computer Science A Go-Back-N (GBN) ARQ scheme has been designed with window-size W = 10 such that it is fully efficient when there are no errors on the channel. Assume that frame size is 20000 bits and the overhead bits are negligible. What is the bit probability error (as seen at Layer 2) that makes the Go-Back-N ARQ 50% efficient?
Frames of 1000 bits are sent over a 106 bps duplex link between two hosts. The propagation time is 25 ms. Frames are to be transmitted into this link to maximally pack them in transit (within the link). 1.1 What is the minimum number of bits (1) that will be required to represent the sequence numbers distinctly? Assume that no time gap needs to be given between transmission of two frames.
Consider a full-duplex 256 Kbps satellite link with a 240 millisecond end-to-end delay. The data frames carry a useful payload of size 12,000 bits. Assume that both ACK and data frames have 320 bits of header information, and that ACK frames carry no data. What is the effective data throughput When using Stop and Wait?
Consider the following scenario: Frames of 12000 bits are sent over a 400kbps channel using a satellite whose propagation delay is 270ms. Acknowledgements are always piggybacked onto data frames. (That is, in the case of stop-and-wait, the next frame cannot be transmitted until the entire frame containing the acknowledgement is received.) Five-bit sequence numbers are used. What is the maximum achievable channel utilization for (a) Stop-and-wait. (b) Protocol 5 (i.e., Go Back N). (c) Protocol 6 (i.e., Selective Repeat)
We have a 1000 m long 10 Mbps communication channel with ARQ protocol. The signal travels at a speed of 2 ∗ 10 ^ 8 ? / ?Assume that no frame is lost or damaged. Confirmation frames, control information are negligible in size.For what range of frame sizes do we get an efficiency of at least 70%?
4
A planet located far from Earth is around 9 x 1010 meters away. If a stop-and-wait protocol is employed for frame transmission on a 64 Mbps point-to-point link, what is the channel utilization? Assume that the speed of light is 3 108 m/s and that the frame size is 32 KB.
800 b frames are sent over a 500 kbps communication channel. The communication channel usesGBN protocol with 3 bit sequence numbers. The propagation delay is 20 ms. Confirmationsare of size 500 b. Headers and control information are negligible in size.What is the maximum efficiency of this channel?
. You are hired to design a reliable byte-stream protocol that uses a sliding window (like TCP). This protocol will run over a 1-Gbps network. The RTT of the network is 140 ms, and the maximum segment lifetime is 60 seconds. How many bits would you include in the AdvertisedWindow and SequenceNum fields of your protocol header?
Suppose that a SW ARQ system with 1-bit sequence numbering has a time-out value that is less than the time required to receive an ACK. Station A sends 5 frames to station B. No errors occur during transmission of all 5 frames. One ACK is lost when it is transmitted the first time (see the following table), and no transmission of that ACK. No errors occur during transmission of the other 4 ACKS. Sketch the sequence of frame exchanges that transpire between stations A and B. (а) error occurs in re- Last digit of your student ID number 0, 1 2, 3 Lost ACK 1 4, 5 6, 7 8, 9 2 3 4
Consider a full-duplex 512 kbps link with length 36,000Km connecting two hosts. The data frames carry a useful payload of size 6000 bits. Assume that both ACK and data frames have 400 bits of header information, and that ACK frames carry no data. The propagation speed along this link is 3×108 m/sec. a) What is the RTT on this link? b) What is the effective useful data throughput, in kbps, when using Stop-and-Wait?