Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches.

Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

A circuit-switched TDM-link uses 1024-bit frames over 16 TDM slots'. a. How many 'circuits’ are supported by this configuration? b. If we allowed the TDM-link to be utilized for "TCP connections", how many simultaneous TCP connections could be supported by the TDM link? (Hint: remember TCP connections is a full-duplex bidirectional stream) If the gross bitrate of this link is 8.192Mbit/s, what is the 'frame rate'? C. d. Given the 'gross bitrate', what would the throughput be (in bits/s, Kbits/s, or Mbits/s, as appropriate) for any ONE 'circuit in this configuration?
Design an Ethernet network to connect a single client PC to a single server. Both the client and the server will connect to their respective workgroup switches via UTP. Their workgroup switches are connected directly by a trunk link. The two switches are 900 meters apart. They need to communicate at 800 Mbps. Your design will specify the locations of any switches and the transmission link between the switches. Then add another client next to the first client. This client will also communicate with the server and will also need 800 Mbps in transmission speed. Again, your design will specify the locations of switches and the transmission link between the switches.
Problem 3 A TDMA system provides 48.6 kbps data rate for a single user over one physical channel when 3 users are supported in a channel with 6 time slots in a frame. When the frame length is Tf = 40 ms, how many bits does one time slot contain?
10. For a 10 Mbps data link using 12,000-bit frames, and assuming that electrical signals propagate at 2.5 x 108 m/s: a. How long does it take to introduce a single frame onto the link? b. How long does it take for the trailing edge of the frame to travel 1,620 km? c. What is the total transmission time of this frame, from start to finish?
Consider a full-duplex 256 Kbps satellite link with a 240 millisecond end-to-end delay. The data frames carry a useful payload of size 12,000 bits. Assume that both ACK and data frames have 320 bits of header information, and that ACK frames carry no data. What is the effective data throughput When using Stop and Wait?
Given a transmission rate of 1 Gbps and a propagation speed of 200m / μ sec , how many meters of cable are needed for a full duplex transmission link to have a minimum capacity of 1500 bytes?
Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During each time slot 8 bits are sent. What is the total transmission rate of the whole link in kbps?
Assume there is a 1 Mbps shared connection (e.g. Ethernet bus). How long (in microseconds) does it take to send a 1000-bit frame over this link?
Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches. (c) Same as (a), but assume the switch implements “cut- through" switching; it is able to begin retransmitting the packet after the first 200 bits have been received.
Computer Science Which of the following statement is true for Path term in SDH Network? a. Points where add/drop signal occurs. b. Points between SDH network Originated and Terminated. c. Points where regeneration of signal occurs. d. Points where Multiplexing/Demultiplexing of signal occurs.
What is the delay of sending a data file from a source station to a destination station? Suppose that the length of the data file is 2 Mbytes and the bandwidth of the channel is 1600 bps, and the network link between the sender and receiver is 20000 Km and the speed of the light inside the link is 2x108 meters/second? Assume that the delay is composed of only transmission time and propagation time.
Five channels, each with a l0a-kHz bandwidth, are to be multiplexed together. What is the minimum bandwidth of the link if there is a need for a guard band of 10kHz between the channels to prevent interference?