1. In design an embedded system, the address space [Oxffff d000, 0xffff ffff] is allocated for peripherals. Assume each peripheral has four of 32-bit control registers, four of 32 bit status registers and 240-byte data buffer. What are the maximum number of peripherals that can be accommodated in this system? Show calculation.

1. In design an embedded system, the address space [Oxffff d000, 0xffff ffff] is allocated for peripherals. Assume each peripheral has four of 32-bit control registers, four of 32 bit status registers and 240-byte data buffer. What are the maximum number of peripherals that can be accommodated in this system? Show calculation.

Name: 1. In design an embedded system, the address space [Oxffff d000, 0xff
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: 1. In design an embedded system, the address space [Oxffff d000, 0xffff ffff] is allocated forperipherals. Assume each peripheral has four of 32-bit control registers, four of 32 bitstatus registers and 240-byte data buffer. What are the maximum num

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Related questions

Q: When it comes to a processor's access to main memory, the loosely connected setup and the symmetric…

A: The symmetric multiprocessing arrangement and the loosely connected design are contrasted: A sort of…

Q: Draw the flow chart, and write an ARM Cortex M0+ assembly program to compute the following…

A: Arm assembly instructions LDR This instruction is used to load destination register with a value…

Q: Acomputer employs RAM chips of 256 x 8 and ROM chips of 1024 x 8. The computer system needs 2K bytes…

A: Step 1: Step 2: Step 3: Step 4:

Q: When it comes to a processor's access to main memory, the loosely connected setup and the symmetric…

A: Comparing the configurations of loose coupling and symmetric multiprocessing: A freely connected…

Q: Question 4 Why must the single-cycle datapath have separate instruction and data memories? The…

A: answer is

Q: Given von Neumann architecture, name three (3) special purpose registers in CPU? Explain and discuss…

A: Actually, register is a used to stores the data/information.

Q: Assume an I/O device may only wait for an interrupt to be handled for up to 1 millisecond, and that…

A: How RISC processors handle interruptions: When I/O devices are not yet prepared to supply data or…

Q: For the below microprogrammed architecture, what is the ALU sequence of actions/micro instruction…

A: Solution:-- 1)The given question is an type of the multiple choice question so some of the options…

Q: It's debatable whether a synchronous bus or an asynchronous bus would be preferable for establishing…

A: Data flow from the CPU to a functional unit connected to the system bus can be synchronous or…

Topic Video

Question

1. In design an embedded system, the address space [Oxffff d000, 0xffff ffff] is allocated for
peripherals. Assume each peripheral has four of 32-bit control registers, four of 32 bit
status registers and 240-byte data buffer. What are the maximum number of peripherals
that can be accommodated in this system? Show calculation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 ::

VIEW

Step 2 ::

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Suppose we have a byte-addressable memory of 20 bytes, built using 4 modules. Draw diagrams showing the distribution of addresses within each module, if we are using (a) highorder interleaving, and (b) low-order interleaving.
4. FIGURE 1 shows how a 3 to 8 line decoder (TTL 74138) can be used in conjunction with NAND gate (TTL 74133) to connect a set of switches to the data bus of a microprocessor system via buffers (TTL 74367). Answer the following questions relating to the diagram: a) What address, in HEX, is required on the address bus in order toread the switches? b) RD and MEMRQare control lines from the CPU. What must their logic state be in order to read the switches? Data bus 74 367 74 133 74 138 A15 D7 DO EN EN Address bus MEMRQ A4 A1 A0 EN TRUTH TABLE CBA|O 12 3 4 5 0 0 00 111 1 1 11 0 0 6 110 1 1 1 1 1 1 0 1 01 10 1 1 1 1 1 0 1 11 1 10 1 1 1 1 1 0 01 1 1101 1 1 10 11 1 1 1 101 1 1 101 1 1 1 1 1 0 1 1 1 11 1 1 1 1 1 1 0 74 367 (part of) FIGURE 1 Data enable Data outputs Input switches
Draw a block diagram of a microprocessor-based system interfaced with 8255, 8254, 8259, 8237, and RAM. Also show clock generator, buffers, transceivers and address decoder in the diagram:use 8088 in minimum mode.
Let's pretend for a moment that we have a byte-addressable computer with 16-bit main memory addresses and 32-bit cache memory blocks, and that it employs two-way set associative mapping. Knowing that each block has eight bytes, please calculate the size of the offset field and provide evidence of your calculations.
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful, do not copy and paste off chatgpt
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful
A computer employs RAM chips of 512 x 8 and ROM chips of 256 x 8. The computer system needs1K bytes of RAM, 2K bytes of ROM, and eight interface units, each with 2 registers. A memory-mapped1/0 configuration is used. The two highest-order bits of the 16 bit address bus are assigned 10 for RAM,11 for ROM, and 00 for interface registers.a. How many RAM and ROM chips are needed?b. Draw a memory-address map for the system.c. Give the address range in hexadecimal for RAM, ROM, and interface.
For a computer with 56-bit physical addresses and a 8-way set associative cache of 64 KB where each cache line has the capacity of holding 32 words. Assume the word size is 3 and the architecture is byte-addressable. Answer the questions below: a.How many bits are needed for tag, index, word offset, and byte offs. Show your derivations and assumptions. b.What are the start and end physical addresses, in hex as discussed in class, for cache line 300? Cache line count starts from 0. c.What is the total size, in KB, of this cache? d.What is the tag value, in hex, of address 0xABCDEF98765432?
Question 4 Why must the single-cycle datapath have separate instruction and data memories? The formats of data and instructions are different in RISC-V, and hence different memories are needed. It is less expensive to have separate memories. The processor operates in one cycle and cannot use a (single-ported) memory for two different accesses within that cycle. All of the above.
(a) Draw a block diagram of a typical Data Acquisition System (DAQ) from transducer to computer. Briefly explain each element. (b) What is the General Purpose Interface Bus (GPIB) and what are the three general classes of devices that can be connected to a GPIB bus? In what standard configurations can devices be connected to the bus? - How many devices can be interconnected to one bus and what address settings can they have?
Computer Science Consider a computation running on a machine with a 1 GHz clock, 8-word cache line, single cycle access to the cache, and 100 ns latency to DRAM. The computation has a cache hit ratio at 1 KB of 40% and at 32 KB of 70%. Consider three cases: (1) a single threaded execution without caches, (2) a single threaded execution in which the entire cache is available to the serial context, and (3) a multithreaded execution with 32 threads where each thread has a cache residency of 1 KB. Calculate the required bandwidths for all the three cases respectively.
Design a memory map for a system with 64 K of memory space, a 16-bit address bus, and a 8-bit data bus. The system needs to meet the following design requirements: The system needs 20 K of RAM, organized in a contiguous block starting at address 0x1000 . The system needs RAM filling the memory range from 0xA000 to 0xCFFF (inclusive) Your design must be subject to the following constraints in terms of access to memory chips: You can use a maximum of two (2) 8 K×8 RAM chips. You can use a maximum of two (2) 4 K×8 RAM chips. You can use a maximum of two (2) 8 K×8 ROM chips. You can use a maximum of two (2) 4 K×4 ROM chips.