1. Given the values of the load L and FR-R-R dimension R, for what value of the couple M will the force in link CH be equal to 10 kN, compressive? Note that R = 2m andL = 50 kN. в м 2R Given: (figure); R = 2m, L = 50kN 7,

1. Given the values of the load L and FR-R-R dimension R, for what value of the couple M will the force in link CH be equal to 10 kN, compressive? Note that R = 2m andL = 50 kN. в м 2R Given: (figure); R = 2m, L = 50kN 7,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places Structural Theory a. Determine the vertical reaction R₂ in KN. b. Determine the shear at midspan between vertical supports in KN c. Determine the maximum factored load moment in the beam in KN.m
View Policies Current Attempt in Progress A simply supported wood beam that is 13.5 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 150 mm, d = 430 mm, a = 65 mm, and c = 20 mm. Section a-a is located at x = 2.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At sectiona-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P a H. a В K L 2L 3. 3 Answer: КРа (a) TH = kPa (b) TK = kPa (c) Tmax MPa (d) Omax = Submit Answer Attempts: 0 of 3 used Sava for Late Using multiple attempts will impact your score, 56 score reduction after attempt 1
Completely solve. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS. BOX THE FINAL ANSWER.
Problem 4 Design the steel reinforcement for the uniaxial eccentrically loaded short column shown below, using the appropriate interaction diagram. Use f. 28 MPa, and fy 420 MPa. %3D Knowing that: e, = 150 mm, and Pn = 2200 kN 100 mm y 300 500 mm mm 300 100 mm mm
2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm fasten together as shown in the figure. Determine the safe diameter of the fasteners if the fasteners as spaced 100mm apart. The allowable shear stress in rivets is T = 145 MPa. 0 A P=20 kN 4m
A simply supported wood beam that is 13.2 m long carries a 41 kN concentrated load at B. The cross-sectional dimensions of the bearn are b = 125 mm, d = 350 mm, a = 110 mm, and c= 35 mm. Section a-a is located at x= 2.2 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entirespan. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P. a H a a B C K 2L 3 3 Answer: (a) TH = i 689 КРа (b) TK = i КРа 280 (c) Tmax= i 799 kPa (d) Omax= 47.11 MPa
Q12. A continuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments. %3D
Q12. Acontinuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments.
A simply supported wood beam that is 9.3 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 400 mm, a = 80 mm, and c = 30 mm. Section a-a is located at x = 1.6 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P y H a A a B C 2L 3 Answer: (a) TH = i kPa kPa (b) TK = i kPa (c) Tmax = i MPa (d) Omax= i
4. A solid rectangular section beam, with cross-section 0.01m × 0.02m, and length 1m is simply supported at each end. A load of 80kg is applied at the middle of the span. The I-value of a rectangular section beam is given by: I = bh3 Calculate the maximum bending stress, ơmax 12