1. Given steam pressure of 900 lb/ft2, temperature of 3000F, specific volume of 5.8 ft3/lb. If the specific enthalpy is 9500 ft-lb/lb, what is the internal energy per lb of the system?

Q: COntext: From the first setup where there is no newspaper present, the ruler fell down easily as I…

A: Given: In the first situation there is no newspaper above the ruler. And in second condition there…

Q: the meaning of the graphics below

A: Given: two graphs are shown in graph (a) load is shown on y axis and deformation is shown on x axis.…

Q: plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll…

A:

Q: Assume the given graph of 10 mm grid, draw the isometric views of objects shown in fig. 11

A:

Q: Draw the FRONT VIEW, TOP VIEW , SIDE VIEW of the figure below • Draw the SURFACE DEVELOPMENT of the…

A:

Q: A robot is moving in a 2D planar world coordinate plane. Starting from the initial point, the robot…

A:

Q: Produce a 3D solid model of the Guard casing and test boss

A: Given Test boss Guard casing To find 3D solid model

Q: Grips appear: a. At key points on drawing objects b. On a separate layer c. Every time you click on…

A: When an object is preselected, the object gets highlighted and little squares will show up on them…

Q: Draw the three-dimensional model of the given picture.

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Draw the three projections of the following figure using AutoCAD software and send the solution in…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: DIMENSION THE OBJECT SHOWN BELOW. NOTE THAT NOT ALL ORTHOGRAPHIC VIEWS WILL REQUIRE DIMEN- SIONS. DO…

A: Orthographic views of a part i.e., Top view and Side/Front view is given here. Grid spacing is…

Q: 4. ㅂ 1

A:

Q: Draw the isometric view

A: Given orthographic view  Front and top

Q: Q1/ Draw Sectional Front view (Front section), Sectional Side view (Side section),and Draw the…

A:

Q: Draw the 3D isometric view of the 2D views of the object given in Figure 4.

A: Please refer the following image for the required 3D isometric view.

Q: Pline command is used to draw a closed models consists of lines only.

A: This question is based on AutoCAD software.

Q: raw the multiview projection of the isometr

A:

Q: Draw the isometric view of the given orthographic projection of the object?

A: According to the details in the kitchen we need to draw isometric view of the given object. I am…

Q: hand three planes of 'orthographic' projection (i.e., top, front, and side views). The dimensions of…

A:

Q: For the objects shown in isometric below, sketch the top, front, and right side views in the space…

A: Given: Draw front, top view and right side view of the given isometric view.

Q: Shown in the image is a vertical section of a 66 block grid of a gold mine deposit. Each block is…

A: Based on the image presented, which includes varying ore grades ranging from 1.4 g/t to 2.9 g/t in…

Q: The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its…

A: Given: Let us consider the resultant of this force system is the couple-vector CR=-1100i+1500j…

Q: Point "P", as shown below, is located between nodes 2 and 3 of a quadratic 1D bar element. Workout…

A: Given data: location of node 1, x1 = 10.8 mm location of node 2, x3 = 34.6 mm location of point P in…

Q: SKETCH THE 2D FIGURE IN AUTOCAD DRAWING AND USE THE 2D SKETCHING TO FIGURE OUT THE BELOW SKETCH

A:

Q: Instruction: Determine the moment of the force about point A.

A: Given Structure in loading To find Moment about A

Q: he Lookout Hills gravitational slope-deformation feature in Bonne Bay, western Newfour plume of rock…

A: 306m wave height has been found in norris point.

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Step 1: Step 2:

Q: Assuming simple graph of 10 mm grid, draw the isometric views of objects shown in fig 2

A:

Q: Draw the isometric figure given the views below. Will thumbs up if correct. Thank you.

A:

Q: For the given multiview projection, draw the corresponding isometric drawing. ME DA

A: For the given multi view projection, draw the corresponding isometric drawing.

Q: 3. The distance between end projectors of a line CD which is inclined 45° to VP, is 60 mm. Point C…

A: the distance between end projector of a line CD which is inclined 45 to VP , is 60mm . point C is…

Q: free hand sketch the isometric view, choose the appropiate scale. given: front and right view.

A: Given Front and right view

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: Draw the isometric perspective and the ortogrophic views of the object (4 views in total). Indicate…

A:

Q: In the following image the two temperature values that are equal are:

A: Given data:-To find:-the two temperature values that are equal

Q: for the given figure , draw the 2d sketch using AutoCad and give the dimension

A:

Q: i need the answer quickly

A: home > line > 0,0> enter >keep mouse in right > type 25>  enter> up >type 10…

Q: The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw…

A: Draw the isometric block according to dimensions of the object as shown in the image:

Q: 3. On the drawing and produced part below, label the following terms: Datum feature symbol Datum…

A: Label the given terms.

Q: Pls show the edge view of two triangles in a single reference plane...kindy explain the steps

A: Solution: Given Data:

Q: For the objects shown in orthographic projection below, construct an isometric Use the box method to…

A: Find Isometric view of the object.

Q: 2 link 1 Draw HGL & EGL. tankz tank 3

A: For the solution refer below images.

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.