1. From the figure shown, the tank contains oil having s specific gravity of 0.80. Oil flows at a certain rate which produces power in the jet equal to 10 hp. Diameter of orifice is 125mm with Cv = 0.95 and Cc = 0.68. Find the pressure at B. 2.80 m Air oil, s = 0.80 -* B

1. From the figure shown, the tank contains oil having s specific gravity of 0.80. Oil flows at a certain rate which produces power in the jet equal to 10 hp. Diameter of orifice is 125mm with Cv = 0.95 and Cc = 0.68. Find the pressure at B. 2.80 m Air oil, s = 0.80 -* B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Exercise#3: The figure shows a system. The system is conservative energy between the two valves CV, and CV2. The differential pressure element at point 1 shows a reading for flow rate. This flow rate is equivalent to AP = 3 mmH20 with k factor of orifice equals 20 m² (used as dimension geometry for the pipe). Another turbine flow meter at point 4 shows a reading for flow rate equals 2.7. Based on the reading of the first flow meter, is the turbine flow meter give the correct reading or not? You can utilize the following given information: diameters at point1&2 are D, = D2 = 0.2 m, Dz = D4 = 2 D2, Q1= 3Q2, P4 = P3 – 200000 Pa ,p = 750 Total heads(or energy)of Bernoulli equation at point 1=Total heads(or energy)of Bernoulli equation at point 2+4m, and point2 point1 Total heads(or energy) of Bernoulli equation at point 3=Total heads(or energy) of Bernoulli equation at point 4+10m. CV, 8 Closed DP · Flow meter h tank Turbine Flowmeter CV2 voint4 point3
Please explain so I can understand
A 12.5mm diameter orifice at the vertical side of the tank showed a discharge of 60 liters for every 85 seconds at a constant total producing head of 4.5m. Measurement of the jet showed that it travelled 2.4m horizontally while dropping 400mm. Determine the coefficient of discharge. A) No Answer among the choices В 0.612 C) 0.637 D 0.584 E 0.668
5-64. A thin rubber tube of 25 mm inside diameter is used to siphon water from the large tank of Figure 5.56. To prevent the tube from collapsing, the pressure inside the tube can not be less than 50% of the pressure outside the tube. Determine the smallest value of h to prevent the siphon from stopping due to collapsing of the tube. 2.5 m 5 m Figure 5.56 System for Exercise 5-64. THANK SUNTETICE Full Michifo Nas s itset SCH
Local atmospheric pressure is 14.2 psia. Determine the absolute pressure in the pipeline.
English (United States) Oil at 80°C (p = 56.8 lbm/ft³ and μ = 0.00278 lbm/ft*s) is flowing steadily in a 0.5-in-diameter, 120-ft-long-pipe. During the flow, the pressure at the pipe inlet and exit is measured to be 120 psi and 14 psi, respectively. Determine the volumetric flow rate of oil through the pipe assuming the pipe is inclined 20° downward. Accessibility: Investigate X TO
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
Why is that the pressure of air P2, the formula is added by 9.81h? Please answer this. Thank you.