1. Find the heat transfer per unit area through the composite wall in Figure below. Assume one-dimensional heat flow. k₁= 150 W/m. C kg = 30 kc = 50 A = 0.1 m² kD=70 B AB=AD C D 7.5 cm 45.0 cm T = 370°C 2.5 cm A T = 66°C

1. Find the heat transfer per unit area through the composite wall in Figure below. Assume one-dimensional heat flow. k₁= 150 W/m. C kg = 30 kc = 50 A = 0.1 m² kD=70 B AB=AD C D 7.5 cm 45.0 cm T = 370°C 2.5 cm A T = 66°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat Transfer question In order to cool down a hot steel sphere (its diameter is 5 cm), CO2 gas is blown over it through a pipe with a diameter of 10 cm. The CO2 gas is kept at atmospheric pressure while moving through a smooth pipe at a speed of 6 m/sec. The gas temperature entering the pipe is 300K and exiting the pipe is 340 K. The pipe temperature at the entrance is 350K and at the exit is 550K. The sphere is located just about the pipe exit. Find the convective heat transfer coefficient of the gas moving in the pipe, the heat transfer rate at the pipe and the pipe length. What is the surface temperature of the sphere if the heat transfer rate between the sphere and the gas is 7W and its surface temperature is higher than the gas?
A long rod with a diameter of 2 cm is welded to the outer wall of the boiler and extends out. The wall temperature of the boiler is 80 °C and the room temperature is 20 °C. At a distance of 3 cm from the boiler wall, the bar temperature is measured as 60 °C. Since the heat transfer coefficient between the rod and the medium is 30 W/m2°C a) find the heat conduction coefficient of the Rod material. b) find the amount of heat lost from the Rod.
The figure shows the cross section of a wall made of three layers. The thicknesses of the layers are L₁, L2=0.750 L₁, and L3 = 0.350 L₁. The thermal conductivities are k₁, k₂ = 0.840 k₁, and k3 = 0.780 k₁. The temperatures at the left and right sides of the wall are TH = 23 °C and Tc = -10 °C, respectively. Thermal conduction is steady. (a) What is the temperature difference AT2 across layer 2 (between the left and right sides of the layer)? If k2 were, instead, equal to 1.160 k₁, (b) would the rate at which energy is conducted through the wall be greater than, less than, or the same as previously, and (c) what would be the value of AT2? TH k₁ L₁ kg|kz kq L₂ L3 Tc
3.10 By neglecting lateral temperature variation in the analysis of fins, h,T. 木 H two-dimensional conduction is modeled as a one-dimensional H problem. То examine this T, h,T. approximation, consider a semi- infinite plate of thickness 2H. The base is maintained at uniform temperature T,. The plate exchanges heat by convection at its semi- infinite surfaces. The heat transfer coefficient is h and the ambient temperature is T.. Determine the heat transfer rate at the base.
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
A house, for cooling purposes, consists of two zones: the atric area zone A and the living area zone B (see below figure). The living area is cooled by a 2 -ton air conditioning unit that removes 23,000 Btu/hr. The heat capacity of zone B is 1/6 °F per thousand Btu. The time constant for heat transfer between zone A and the outside is 3ℎr, between zone B and the outside is 6ℎr, and between the two zones is 6ℎr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A ?
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. Illustrate the order of arrangement of bricks A and B in the furnace wall (with thickness, estimated temperatures at the interface between walls A and B and at the interior and exterior surface, the transport area and direction of transfer included)
As shown in the sketh below, a steam pipe of 0.12-m inside diameter is insulated with a layer of calcium silicate. "2. Ta2} 1. Ta,1} Steam Insulation (a) If the insulation is 10 mm thick and its inner and outer surfaces are maintained at T, = 800 K and Ta = 490 K. respectively,. what is the rate of heat loss per unit length (q) of the pipe, in W/m? (b) Determine the rate of heat loss per unit length (d), in W/m, and outer surface temperature T,2, in K, for the steam pipe with the Inner surface temperature fixed at T = 800 K, inner radius = 0.06 m, and outer radius n = 0.18 m. The outer surface is exposed to an airflow (T 25°C) that maintains a convection coefficient of h = 25 W/m2-K and to large surroundings for which Tur = T, = 25°C. The surface emissivity of calcium silicate is approximately 0.8.
An external wall of a building has a U value of 0.50 W/m^2K. The indoor temperature is21 degrees C and the outdoor temperature is -2.0 degrees C The steady-state heat loss is calculated to be 11.5W/m^2 The wall contains a layer of insulation 40 mm thick with a conductivity of0.035 W/mK. What would the insulation thickness need to be in order toreduce the steady state heat loss by 50%? answer = 0.11m please show all working
A square steel bar of side length w = 0.21 m has a thermal conductivity of k = 15.6 J/(s⋅m⋅°C) and is L = 2.7 m long. One end is placed near a blowtorch so that the temperature is T1 = 95° C while the other end rests on a block of ice so that the temperature is a constant T2. a. input an expression for the heat transferred to the cold end of the bar as a function of time using A=w^2 as the cross-sectional area of the bar. b. how much energy in joules was conducted in 1 hour, assuming t2=0*C c. input an expression for the mass of the water melted in one hour using Q1 from above and Lf in the latent heat of fusion. mw=
A house, for cooling purposes, consists of two zones: the attic area zone A and the living area zone B (see below figure). The living area is cooled by a 2-ton air conditioning unit that removes °F per thousand Btu. The time constant for heat 19 4 41,000 Btu/hr. The heat capacity of zone B is transfer between zone A and the outside is 2 hr, between zone B and the outside is 4 hr, and between the two zones is 4 hr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A? It eventually gets to be F in the attic zone A. (Type an integer or decimal rounded to the nearest hundredth as needed.) 4 hr 쉽 A H 4 hr B 2 hr MIN 41,000 Btu/hr