A house, for cooling purposes, consists of two zones: the attic area zone A and the living area zone B (see below figure). The living area is cooled by a 2-ton air conditioning unit that removes 10 41,000 Btu/hr. The heat capacity of zone B is °F per thousand Btu. The time constant for heat 4 transfer between zone A and the outside is 2 hr, between zone B and the outside is 4 hr, and between the two zones is 4 hr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A?

A house, for cooling purposes, consists of two zones: the attic area zone A and the living area zone B (see below figure). The living area is cooled by a 2-ton air conditioning unit that removes 10 41,000 Btu/hr. The heat capacity of zone B is °F per thousand Btu. The time constant for heat 4 transfer between zone A and the outside is 2 hr, between zone B and the outside is 4 hr, and between the two zones is 4 hr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vertical cylinder contains v moles of an ideal gas and is closed off by a piston of mass and area A. The acceleration due to gravity is g. The molar specific heat cy (at constant volume) of the gas is a constant independent of temperature. The heat capacities of the piston und cylinder are negligibly small and any fric- tional forees between the piston and the cylinder walls can be neglected. The whole system is thermaly insulated. Initially, the piston is clamped in position so that the gas has a volume Ve and a tomperature Tn. The pıston is now released and, after some nscillations, comes to rest in a final equilibrium situation corresponding to a larger volumc of the gas. (@) Does the temperature of the gas increase, decrease, or remain the same? (b) Does the entropy of the gas increase, decrease, or remain the same? (c) Calculate the final temperature of the gas in terms of Te, lo, unl the other parameters mentioned in the statement of the prublem.
Please solve fast.
I need the answer as soon as possible
Give an example of application of the Oth law of thermodynamics in everyday life. List explicitly Systems 1, 2, and 3 and what is the purpose of them being at the same temperature.
A house, for cooling purposes, consists of two zones: the atric area zone A and the living area zone B (see below figure). The living area is cooled by a 2 -ton air conditioning unit that removes 23,000 Btu/hr. The heat capacity of zone B is 1/6 °F per thousand Btu. The time constant for heat transfer between zone A and the outside is 3ℎr, between zone B and the outside is 6ℎr, and between the two zones is 6ℎr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A ?
3. 100-gram oil at 20°C and 50-gram iron at 75 °C are placed in 200-gram iron container. The increase in temperature of the container is 5°C and the specific heat of oil is 0.43 cal/g °C. What is the specific heat of the iron?
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
I need answer within 20 minutes please please with my best wishes
In an experiment to measure the specific heat of material, a student first measured the masses of the following samples as given in Table 1. Table 1: Measurement of Mass Physical quantity measured in (g) Value Mass of Styrofoam 2.4 cup Mass of Styrofoam 62 cup + water Mass of Brass sample 15.3 Mass of Copper sample 62.5 and then recorded the temperatures of the above two samples, in Table 2. Table 2: Measured values of Temperatures Hot termperature ("C ) Sample Equilibrium cold temperature ( C) temperature ("C) Brass 99.8 26.5 24.5 Сopper 99.8 32 26 Answer the following questions using the data given in Table 1 and Table 2. (Please enter the answers with two digits after decimal) (a) Calculation of specific heat capacity of Brass: Calculated Quantities Mass of the water (in Values grams) Change in temperature lof the hot object ( ATobieca) °C) Change in temperature of water (ATwaer) (°C) Calculated specific heat of the object in (cal/g'C) (b) Calculation of the specific heat capacity…
3. The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal conductivity is 60 W/m-C. The voltage and current flowing into the heater are 220V and 5A, respectively. Find the temperature at the top portion of the pan.
A refrigerator has a coefficient of performance of 2.50, requires 150 W of electrical power to operate, and maintains a temperature of -4.00 °C within its interior compartment. How long would it take to cool a dozen 1.00 L of water in a plastic wrapper from 33.0 °C to -4.00 °C in this refrigerator? Any heat escaping the plastic should be ignored. Remember that 1.00 g/cm3 is the density of water.