1. Each of the two sides of a hand-operated toaster can be operated independently of the other. A spring holds each side of the toaster shut, and each side must be held open in order to insert bread. Assume that the toaster is hot and ready to toast bread. The following are the elemental times necessary to perform the operations. Assume also that both hands can perform their tasks with the same degree of efficiency. Side • Place slice of bread in either side of toaster: 4 seconds. • Toast either side of bread: 30 seconds. • Turn slice of bread on either side of toaster: 2 seconds. • Remove toast from either side of toaster: 4 seconds. Side B By using a man machine chart for toasting 3 slices of bread, what method would you recommend to obtain the best equipment utilization that is, the very shortest overall time?

1. Each of the two sides of a hand-operated toaster can be operated independently of the other. A spring holds each side of the toaster shut, and each side must be held open in order to insert bread. Assume that the toaster is hot and ready to toast bread. The following are the elemental times necessary to perform the operations. Assume also that both hands can perform their tasks with the same degree of efficiency. Side • Place slice of bread in either side of toaster: 4 seconds. • Toast either side of bread: 30 seconds. • Turn slice of bread on either side of toaster: 2 seconds. • Remove toast from either side of toaster: 4 seconds. Side B By using a man machine chart for toasting 3 slices of bread, what method would you recommend to obtain the best equipment utilization that is, the very shortest overall time?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. Which is NOT a generally accepted principle in tabulation? a. C. Every table should be given a distinct number to facilitate easy reference. d. b. The units of measurement under each heading or sub-heading must always be indicated. Use abbreviations when the heading is very long. Place the miscellaneous and exeptional items in the last row of the table.
Follow the instructions carefully
Please help. Written on paper not typed on computer or keyboard please. Need help on both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
I need help answering these 3 parts. 1. The size description of an object on the print can best be described as dimensioning. TRUE or FALSE 2. The amount that any one dimension can vary is referred to as the tolerance. TRUE OR FALSE 3. While the MMC of a feature is important, for certain design calculations, it is important to also understand the LMC. TRUE or FALSE
Please help solve this problem!!
The height of an object would be found on which of the standard views in a set of drawings
PLEASE ANSWER QUICKLY WITHIN 30 MINUTES
A micrometre is a precision measuring instrument, with 50 division on the thimble. Select one: True False
Applying the technique of tool radius compensation write a program to cut the external profile of the part shown below using the following data: PART TOOL S (rpm) Depth (mm) F (mm/min) 400 130X130X10 mm T1 08 Flat End Mill 2000 10 9 130 P15 P16 R4 P4 P3 P13 P14 R40 P2 PL R30 8 130 20 R4! P12 P11 P7 P8 PO (0, -45, 2) 40 80 Fig.: A Clamping Jaw P5 P6 P10 35 P9 08
FIGURE below shows a typical tester used in a mechanical workshop. Answer the questions tha follow. USF aleil äis UI a. Identify the tester shown in FIGURE b, Label the parts of the tester marked C. State the purpose of the tester shown in n ng An box at the last cheet
Give a steps by steps answer of the solution
answer a & b. Please show all your work!!