5. Which is NOT a generally accepted principle in tabulation? a. b. Every table should be given a distinct number to facilitate easy reference. The units of measurement under each heading or sub-heading must always be indicated. Use abbreviations when the heading is very long. d. Place the miscellaneous and exeptional items in the last row of the table.

5. Which is NOT a generally accepted principle in tabulation? a. b. Every table should be given a distinct number to facilitate easy reference. The units of measurement under each heading or sub-heading must always be indicated. Use abbreviations when the heading is very long. d. Place the miscellaneous and exeptional items in the last row of the table.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE DIMENSIONS NEED TO BE PLACED, NO NEED TO PUT THE ACTUAL NUMERICAL VALUES JUST USE LETTERING A, B, C, ETC.
I need help solving problem numbers 4--15.
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
9. One of the following is a glass disk that fits in a microscope eyepiece that has a ruled scale, which is used to measure the size of magnified objects: A. Optical flats B. Optical projector C. Ocular lens scale D. Industrial magnifiers E. Shup microscope
I need help solving problems 7, 11, and 12 pertaining to the print provided below.
I need help answering this quick review pertaining to the print provided.
When no geometric tolerance is specified, the size tolerance controls the well as the size. O form orientation O profile O position as
I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…