The Diagram below summerize what is a manufacturin system, can you explain it? Inputs Disturbances Outputs Good products. good parts, etc. Material A Manufacturing System is Energy A complex arrangement of Information Demand wwww physical elements Service to customer Social characterized by measurable Defectives and scrap Political Information parameters. External customer

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A: The initial conditions are: The specific volume of the steam can be determined from the steam table…

Q: Please check for the question, verify it is correct or not?

A: There is a half cylinder with length L and radius r.Incoming air velocity is uCoefficient of the…

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: hi still waiting on the last part of the question..

A: Application of ballast tanks in aerospace

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: A particle P of mass m = 3 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Given:

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: Is this the only correct option in the question above? I think the question is worded for more than…

A: To elaborate why a sling psychrometer can measure humidity.

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

A:

Q: Which of the following statements below are incorrect? select all which apply.     A shear force…

A: It is needed to provide the wrong or incorrect statements.

Q: The Answer is cut off on the right side.

A: