1. Based on what was observed in the Oersted experiment: Do the experiment at home using the following materials: a compass, a conducting wire and any 1.5 V battery. With the photos you will evidence his experiment. Warning: Never leave the circuit connected for a long time because it can catch fire and the conductive wire, being short-circuited, increases its temperature very quickly and can burn. Only connect for a few seconds long enough to observe the experiment. 2. Show through a graph or a brief description of how to use the "law of the right hand" to determine the direction of the magnetic field that is produced when a current flows through a conductor.

1. Based on what was observed in the Oersted experiment: Do the experiment at home using the following materials: a compass, a conducting wire and any 1.5 V battery. With the photos you will evidence his experiment. Warning: Never leave the circuit connected for a long time because it can catch fire and the conductive wire, being short-circuited, increases its temperature very quickly and can burn. Only connect for a few seconds long enough to observe the experiment. 2. Show through a graph or a brief description of how to use the "law of the right hand" to determine the direction of the magnetic field that is produced when a current flows through a conductor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

TII 5.) A 5.5 mm2 THHN Cu Wire will have this ampacity if it is used at an ambient temperature of 36⁰C. A. 8.0 B. 14 C. 22 D. Either B or C
3. The resistance of a copper wire at 70°C is 150 ohms. If the temperature coefficient of a copper at 0'C is 0.004261, What is the resistance at 20°C?
a. Patch clamp recording of a single ion channel yields the following results: Holding Potential (mV) Measured Current (pA) -100 -1.0 -50 0.0 0 +1.0 +50 +2.0 +100 +3.0 What is the electrical resistance (in ohms) of this channel? (keep in mind mV = 10-3 volts, pA = 10-12 amperes, and an ohm is a derived unit that is equivalent to a volt/ampere, i.e. a V/A). a.) 1 x 1010 ohms b.) 2 x 1011 ohms c.) 5 x 1010 ohms d.) 2 x 10-11 ohms e.) 5 x 10-10 ohms b. What is the conductance of this channel in siemens (S)? (keep in mind 1 S = 1/ohm) a.) 2 x 1011 S b.) 5 x 1010 S c.) 1 x 10-11 S d.) 2 x 10-11 S e.) 5 x 10-10 S c. What would be the equivalent conductance of 1,000 of these channels opened at the same time? a.) 1000 x conductance of 1 channel b.) 5 x 10-8 S c.) 2 x 10-14 S d.) 1/1000 the conductance of 1 channel e.) 2 x 108 S
A series circuit is set up with an AA battery along with an mystery material and ammeter; however, there’s no current passing through. A.Insulator B.Conductor C.Semiconductor
3. Suppose that these atomic configurations belong to Al at 30 °C, Select the correct answer about electrical resistivity? (1) (2) (3) Perfect Crystal terst impurity t Low defects No defects High defects
A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normal operating temperature of the wire is 40°C. What is the maximum current the wire can carry for 1 second without exceeding the NEMA temperature rating?
3.- For the following circuit, determine the following:(a) Currents in each branch. b) Potential differences between each branch (from junction to junction). c) Electric potentials in each junction with respect to ground
Please answer it with complete solution with explanation! Thank you. Calculate the resistance at 20° C of copper wire whose diameter is 56.745 mils and length is 304.8 meters. The resistivity of copper is 1.724 micro-ohm cm at 20° C.
A) Find the equivalent resistor of the circle between points a and b?B) If a constant voltage source (15V) is placed between points a and b, calculate a valueCurrent iS
For the circuit, determine (a) the current supplied by each battery, (b) the current through the 15-ohm resistor and (c) the p.d. across the 10-resistor.
Calculate the supply voltage necessary for charging a battery of 110cells or 30A (i)at the beginning of charge and (ii)at the end of the charge, If each cell possesses p.d.of 2.1 volts at the beginning and 2.7 volts at the end of charge.Allow 0.06 for the resistance of the connecting leads.