1. An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 1 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small angle analysis. 200 mm 400 mm P = 2 kN

1. An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 1 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small angle analysis. 200 mm 400 mm P = 2 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the final measurements of the length and diameter of the following bar that is subjected to a force of 50kN. Assume that the material behaves elastically with a modulus of elasticity of 200GPa and a Poisson's modulus of 0.32. P = 50 kN 600 mm 20 mm E=200 GPa V=0.32 P = 50 kN
Determine the elastic modulus and the yield strength for the material having the stress-strain curve shown. Use the 0.2% offset method. 1600 1400 1200 E 1000 800 600 400 200 0.5 1 1.5 2 Strain, percent Elastic modulus: (Express your answer in whole numbers.) E = ksi Yield strength: (Express your answer using three significant figures.) Sy = ksi Stress, psi
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is oy = 473 MPa, whereas that used for the rectangular cross- section is 0.850y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 77 mm, b=46 mm, a=11 mm, H=77 mm, d= 46 mm N b h a + N a | d H
The cross-sectional diameter of aluminum nail measures 1.50 mm and it is projected outward to a length of 3.50 cm horizontally from a wall. A wet raincoat having a mass of 2.60 kg is hanged on one end of the nail. Assuming the wall holds the other end of the nail, what is the vertical deflection at end of the nail where the raincoat is hanged? The shear modulus of aluminum is 2.40×101º N/m². 4.
The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
Solve it quickly please
A continuous and aligned fibrous reinforced composite having a cross-sectional area of 975 mm, then the area is subjectedi to an extenal tensile load. If the stresses sustained by the fibre and matrix phases are 215 MPa and 5.38 MPa, respectively, the force sustained by the fibre phase is 76,800 N, and the total longitudinal composite strain is 1.56x103 then determine.
Determine the bulk modulus for each of the following materials: (a) rubber, Er = 0.4 ksi, nr = 0.48, and (b) glass, Eg = 8(103) ksi, ng = 0.24.
A sample of silicone breast implant, polydimethylsiloxane (PDMS), is placed under unconfined compression. The magnitudes of the resulting longitudinal and transverse strains have been measured to be 2.7 and 1.341, respectively. The young's modulus of the implant is 500 kPa. Calculate the shear and bulk moduli.
The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L = 460 mm, H = 345 mm, d₁ = 3 mm, d₂ = 5 mm, d3 = 13 mm, d4 = 8 mm, d5 = 3 mm, and de = 6 mm. Figure H B A dz dg ds + 1 of 1 Part A Determine the shear strain Yzy at corner A. Express your answer to three significant figures and include appropriate units. ol Di μA ? (YA)zy = Value Units Submit Request Answer Part B Determine the shear strain Yzy at corner B. Express your answer to three significant figures and include appropriate units. Di μA ? (YB)Ty = Value Units Submit Provide Feedback Request Answer
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 8 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1.6 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 4.1 x 10-3. Solution Cross-sectional Area, A (in mm²) Tensile Load, F (in N) Length of the Specimen (in mm)
C1=150 C2=110