1. a) Two generating units has the following fuel cost, determine the economic load scheduling of the Generators if the Load Demand is 500 MW. Assume both generators are operating at all times and power loss is neglected. Calculate the Fuel Cost of the generators and also Incremental Fuel cost of the generators and write your inference. Also calculate the Fuel cost if the Load demand is ZERO. 100 MW ≤ Pg1 ≤ 650 MW 50 MW ≤ Pg2 ≤ 500 MW F₁ = 0.16 P₁² + 0.22 Pel + 100

1. a) Two generating units has the following fuel cost, determine the economic load scheduling of the Generators if the Load Demand is 500 MW. Assume both generators are operating at all times and power loss is neglected. Calculate the Fuel Cost of the generators and also Incremental Fuel cost of the generators and write your inference. Also calculate the Fuel cost if the Load demand is ZERO. 100 MW ≤ Pg1 ≤ 650 MW 50 MW ≤ Pg2 ≤ 500 MW F₁ = 0.16 P₁² + 0.22 Pel + 100

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A shunt generator running at 1000 r.p.m. has generated e.m.f. as 350 V. If the speed increases to…

A: We need to find out the generated emf at different speed .

Q: Q-A power generating station has a maximum demand of 1000 MW. The annual load factor is 75% and…

Q: The maximum demand of a power station is 110 MW. It generates 105 x 10 units during the day. The…

Q: Explain the concept of demand response and its significance in modern power system

A: Demand response (DR), which is a strategy for controlling electricity usage in response to changes…

Q: 4 Electric power is to be generated by installing a hydraulic turbine-generator at a site 70 m below…

Q: a. The value of excitation current required for full load current at 0.7 pf lagging (over-excited).…

A: The alternator is a machine which converts mechanical energy to electrical energy. It generates…

Q: Voltage drop due to IaRa is at right angle to Ia in synchronous machine working at lagging power…

Q: A three-phase synchronous generator with a nominal pole voltage of 3300 V, nominal apparent power of…

A: The objective of the question is to calculate the real power absorbed by the load during nominal…

Q: K J102 In the circuit shown, the load consumed (500VA) with (0.8) power factor. Compute the coupling…

Q: A generating station has a maximum demand of 25MW, a load factor of 70%, a plant capacity factor of…

A: In this question, we will find reserve capacity, daily energy produced..

Q: Turbine operating efficiency is not influence to maintain the minimum cost of power generation True…

A: Turbine operating efficiency is an important parameter to maintain the minimum cost of power…

Q: Explain in your own words and your own understanding (avoid plagiarism) why there's a need to do…

A: Power quality is fundamental for productive gear activity, and force factor adds to this. Power…

Q: A wind farm operator currently has a wind farm situated on cropland that has: Four 250KW machines…

A: Given: At a hub height of 30 m Wind velocity, v=7 m/s Blades length, r=13.5 m

Q: Two alternators operating in parallel supply 2516 KW to a load at a lagging power factor of 80%If…

Q: Induction motors and power factor correction capacitor banks are examples of nonlinear loads. True…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: How does power factor correction influence the efficiency of power systems, and what technologies…

A: Here we need to explain how does power factor correction influences the efficiency of power systems…

Q: In power factor correction where a motor load is normally operating with 1000 inductive vars, a…

A: It is mentioned, that in power factor correction when motor loads operate with 1000 inductive VARS…

Q: 4. For a simple two-generator power system with the following generation functions: F₁(P) = 120 +…

Q: A generating station has a maximum demand of 20MW,a load factor of 60%, a plant capacity factor of…

Q: 5 10 15 20 25 30 Wind speed From the power curve above, estimate the value of the following: t-in…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: b) For the following applications which type of DC motors do you select? Explain the reason. i)…

A: (b) According to the type of application dc motors are selected. For: (i) Electric train: DC series…

Q: Given the following unit step response of a second order system, calculate the following values: 1.…

A: The above plot is the standard plot of tep response of a 2nd order system. Peak time is defined as…

Q: 5-25 Electric power is to be generated by installing a hydraulic turbine-generator at a site 110 m…

A: Given data: The mass flow rate, m=900 kg/s. The hydraulic turbine generator, h=110 m The mechanical…

Q: a question by considering the annual load time curve for an electric station as a straight line from…

A: Total Capacity = sum of individual maximum capacity Capacitance coefficient is the ratio of maximum…

Q: What price would you have to get for the electricity you produce to obtain a 10% return on the plant…

A: As per Bartleby guidelines I can give solution for the first question only as second part is having…

Q: Q.5 Explain why are some parts of electrical machines laminated? [CO-1; CO-3]

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: A generating station has a maximum demand of 55MW, a load factor of 63 %, a plant capacity factor of…

A: In this question load factor , use factor, capacity factor ,maximum demand given....We have to find…

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

1. a) Two generating units has the following fuel cost, determine the economic load
scheduling of the Generators if the Load Demand is 500 MW. Assume both generators are
operating at all times and power loss is neglected. Calculate the Fuel Cost of the generators
and also Incremental Fuel cost of the generators and write your inference. Also calculate the
Fuel cost if the Load demand is ZERO.
100 MW ≤ Pg1 ≤ 650 MW
50 MW Pg2 ≤ 500 MW
F₁ = 0.16 Pg1² + 0.22 Pg1 + 100
F2 = 0.0080 Pg2² +0.22 Pg2 + 220

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

THydropower Plant System The following nametag is specification of a generator in a hydropower plant. MITSUBISHI AC GENERATOR Output Voltage 4. 84.5 MVA 11 kV Current Frequency Speed Power Factor 4435 A 50 Hz 600 RPM 0.86 |Calculate the generated peak voltage. | Calculate real power of the following generator. How many pair-of-poles installed in the generator? Why does not the generator consist of one pair-of-poles only? J Why for water turbine the speed is 600 rpm not 3000 rpm such as in steam turbine? a. b. C. d. е. f. Explain why the turbine is located below the generator.
a question by considering the annual load time curve for an electric station as a straight line from 20mw to 3mw, and to cover these loads, then operate three generating units, the first and second, each with a capacity of 10mw, while the third has a capacity of 5mw, and illustrate the load time curve by drawing, then find: 1- the total capacity of the station 2- the maximum demand 3- capacitance coefficient 4- pregnancy coefficient 5 utilizatio
Help soon.thanks.
TUTORIAL PROBLEMS 1. A generating station has a connected load of 40 MW and a maximum demand of 20 MW : the units |(1) 0-5 (i) 34-25%] 2. A 100 MW powers stations delivers 100 MW for 2 hours, 50 MW for 8 hours and is shut down for the rest of each day. It is also shut down for maintenance for 60 days each year. Calculate its annual load |21%J 3. A power station is to supply four regions of loads whose peak values are 10,000 kW, 5000 kW, 8000 kW and 7000 kW. The diversity factor of the load at the station is 1.5 and the average annual load factor is 60%. Calculate the maximum demand on the station and annual energy supplied from the station. |20,000 kW ; 105-12x10 kWh] generated being 60 x 10°. Calculate (i) the demand factor (i) the load factor. factor. 4. A generating station supplies the following loads : 15000 kW, 12000 kW, 8500 kW, 6000 kW and 450 kW. The station has a maximum demand of 22000 kW. The annual load factor of the station is 48%. Calculate (i) the number of units…
1- Your company is considering the installation of a 2 MW wind turbine with a rotor diameter of 80 m in a location with average wind v = 10 m/s. The turbine has a cut-in velocity of 5 m/s and a cut-out velocity of 25 m/s. The capacity factor is 0.45. The installed cost of the turbine is $3,500,000. Operating expenses are $225,000 per year. The system has a power coefficient (electric power generated divided by wind power) of 0.45. What price would you have to get for the electricity you produce to obtain a 10% return on the plant investment assuming a project lifetime of 20 years? Use the tables for the cumulative wind power distribution in the notes on wind probability to answer this question. Assume an air density of 1.225 kg/m3.
B) Four regions of peak loads 5 MW, 7 MW, 8 MW and 10 MW are supplied by a generating station. The average annual load factor is 0.6 and the diversity factor at the station is 1.5. Calculate: (i) Annual energy supplied by the station (ii) The maximum demand on the station. (iii) If the installed capacity is greater than maximum demand by 20%, suggest the best number of units should be used to cover the load curve
I need the answer as soon as possible
Solve asap with right explanation. Direct answers will be downvoted. Don't copy from other sources.
e)
How does power factor correction impact the efficiency and reliability of power systems?
A generating station has a maximum demand of 30MW, a load factor of 65%, a plant capacity factor of 50% and a plant use factor of 72%. Solve for the reserve capacity of the plant, daily energy produced and maximum energy that could be produced daily if the plant while running as per schedule, were fully loaded.