A man is dragging a trunk up the loading ramp of a mover's truck. The ramp has a slope angle of 20.0o, and the man pulls upward with a force ? whose direction makes an angle of 30.0 with the ramp (Figure 4.9).a) How large a force ? is necessary for the component ??parallel to the ramp to be 43.3N? b) How large will the component ?? perpendicular to the ramp then be? 1. A man is dragging a trunk up the loading ramp of a mover'struck. The ramp has a slope angle of 20.0°, and the man pullsupward with a force F whose direction makes an angle of30.0 with the ramp (Figure 4.9).a) How large a force F is necessary for the component F,parallel to the ramp to be 43.3N?b) How large will the component F, perpendicular to the rampthen be?20.0

The ramp makes an angle with the horizontal of 20° Force applied to the trunk=F This force makes an…

1. A man is dragging a trunk up the loading ramp of a mover's truck. The ramp has a slope angle of 20.0°, and the man pulls upward with a force F whose direction makes an angle of 30.0 with the ramp (Figure 4.9). a) How large a force F is necessary for the component F, parallel to the ramp to be 43.3N? b) How large will the component F, perpendicular to the ramp then be? 20.0

1. A man is dragging a trunk up the loading ramp of a mover's truck. The ramp has a slope angle of 20.0°, and the man pulls upward with a force F whose direction makes an angle of 30.0 with the ramp (Figure 4.9). a) How large a force F is necessary for the component F, parallel to the ramp to be 43.3N? b) How large will the component F, perpendicular to the ramp then be? 20.0

Similar questions

Please draw the free diagram clear and also indicate if we need to add force
1.) Consider the diagram below. Mass Ma = 5kg and Mb = 50kg. The coefficient of kinetic friction between the black Ma and the table top is .2 = uk. Assume the tension in the cord is uniform throughout its length, the acceleration of each block is the same, and the pulley has no mass or friction. Calculate: a.) The acceleration in the system. b.) The tension T in the cord. mA mB
A 1200-kg car is held in place by a light cable on a very smooth (frictionless) ramp, as shown in the figure (Figure 1). The cable makes an angle of 31.0 above the surface of the ramp, and the ramp itself rises at 25.0 above the horizontal. Find the tension in the cable and how hard does the surface of the ramp push on the car?
Needs Complete typed solution with 100 % accuracy.
please help me to answer this quetion with in 30 mins and make sure u get the same number for the answer given below .Thank you !
It's asking Fx and Fy in reference to the foot being held by Ft
The previous step focused on friction for horizontal surfaces. As we discussed above, angled surfaces like the wedge below have different considerations. FN = mg cos(0) F₁ = mg F₁ = ? F₁ = ? Fy=mg cos(0) Specifically, we have the following considerations. 1. The normal force is not equal to mg. 2. There is a force acting along the angle of the wedge due to gravity. What is the coefficient of static friction ? Fx = mg sin(0) Let's consider the implications of this type of problem with the following examples. For all of the examples, the box has a mass of 25 kg. Imagine the box is on a surface that allows you to adjust the incline angle, 0. You find the maximum angle where the box remains stationary. That is, at any higher angle, and the box begins to slide. The static friction force at this maximum angle is 150 N. What is the angle 0 (in degrees)? Now you raise the incline to an angle of 60° greater than the angle of maximum static friction found above. At this angle, the box slides…