1. A closed vat contains oil (sg 0.90) with its liquidsurface located 2 ft from the top if the vat is 25 ftlong and 12 ft deep and has a trapezoidal crosssection 10 ft wide at the bottom and 16 ft wide atthe top, determine the weight (in pounds) of theoil.2. What force "F" in the handle is needed to lift the860kg mass for the hydraulic press filled with oilas shown. Use specific gravity of oil equal to 0.84860 kgOil100-mm diameter-15cm8cm30cm25-mm diameter

Note:- As per the guidelines we are supposed to answer only first question, Repost the another one.

1. A closed vat contains oil (sg 0.90) with its liquid surface located 2 ft from the top if the vat is 25 ft long and 12 ft deep and has a trapezoidal cross section 10 ft wide at the bottom and 16 ft wide at the top, determine the weight (in pounds) of the oil.

1. A closed vat contains oil (sg 0.90) with its liquid surface located 2 ft from the top if the vat is 25 ft long and 12 ft deep and has a trapezoidal cross section 10 ft wide at the bottom and 16 ft wide at the top, determine the weight (in pounds) of the oil.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I want the solution in less than 15 minutes
Show solution 6
Calculate the minimum dimension of a particle that can be completely removed from a settling chamber, if the rate of overflow is 30 m/d/m?. Take specific gravity of particle equal to 2.65 and the dynamic viscosity equal to 1 x 10-5 Ns /m².
For the parallel pipe system shown below, the elevation of point A is 300 feet and a pressure of 30 psi and the elevation of point B is 100 feet with a pressure of 27 psi. What is the approximate flow percentage in the middle red pipe? ● ● ● ● DMain = 12" D₁ = 4" D₂ = 6" D3 = 8" O 19.3 % O 36.9 % O 58.5 % O 70.8 % A ● ● CHWMain = 140 CHW₁ = 100 CHW₂ = 118 CHW3 = 132 B ● L₁ = 1,000' L₂=800' L3= 2,000'
2. Two capillary tubes are placed vertically in an open container of water. One tube has a diameter of 2.0 mm, and the other a diameter of 1.0 inch. In which tube will the water rise higher?
1. An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of the oil is 50 m. Find the corresponding height of water at the point.
From the given figure: Tank 10m Yol = 8kN/m %3D G.S. 4m SAND 6m CLAY Determine the loss in pore water pressure if the degree of consolidation is 30 %. A. 56 kPa 50 kPa 30 kPa D 24 kPa
Q5/ In a test to determine the bulk modulus of a liquid it was found that as the absolute pres- sure was changed from 15 to 3000 psi the volume decreased from 10.240 to 10.138 in.³ Determine the bulk modulus for this liquid.
i need the answer quickly
A smooth concrete pipe with a 1.5 ft diameter carries carbon tetrachloride at 20 C from a tank to a facility 1 mile away, where it discharges into the air. The pipe begins in the tank 3 feet below the surface and descends on a 1:100 (vertical: horizontal) slope. Determine the flow rate, assuming minor losses are negligible.
QI:- Design a settling tank for a flow of 0.2 MGD if the overflow rate is not to exceed 600 gpd/n. Calculate dimensions if the tank is circular with a depth of 12 ft. Calculate dimensions if the tank is rectangular with a depth of 10 fit and a length to width ratio of 4 to 1 Q2:- The settling velocity of alum floc is approximately 0.0014 f/s in water at 10 C. Calculate the cquivalent overflow rate in gpd/f12. What is the minimum detention time in hours to settle out alum floc in an ideal basin with a depth of 10 ft? Q3:- Two rectangular clarifiers, cach 30 ft long, 15 ft wide, settle 0.40 MGD following alum coagulation. The effluent channels have a total weir length of 60 ft. Calculate the detention time, horizontal velocity, rate of flow over the outlet weir. Do these values meet the GLUMRB Standards for water works? Q4:- Calculate the diameter and depth of a circular sedimentation basin for a design flow of 3800 m3/d based on an overflow rate of 0.00024 m's and a detention time of 3…
Cumpute the plasticity index and liquidity index