1. A 175mm x 100mm x 18mm angular section having an area of 4960mm^2 is connected by two rows of 16mm dia. Bolts with a hole diameter of 18mm in the 175mm leg and one row in the 100mm leg. Compute the spacing (pitch S) so that only two holes for 16mm fasteners need to be deducted in computing the net area. 18 100 mm 62.5 mm 18 mm 62.5 mim 75 37.5 mm 175 mm O O ΦΙΦ S O 62.5 g=107 75 37.5 E Os D O O O o + o IS 282 mm

1. A 175mm x 100mm x 18mm angular section having an area of 4960mm^2 is connected by two rows of 16mm dia. Bolts with a hole diameter of 18mm in the 175mm leg and one row in the 100mm leg. Compute the spacing (pitch S) so that only two holes for 16mm fasteners need to be deducted in computing the net area. 18 100 mm 62.5 mm 18 mm 62.5 mim 75 37.5 mm 175 mm O O ΦΙΦ S O 62.5 g=107 75 37.5 E Os D O O O o + o IS 282 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bolted connection shown is made up of 2L150 x 100 x 9.5 mm. The angle is made of A-36 steel and the bolts have diameter of 22 mm. Properties of 2L150 x 100 x 9.5 mm: A = 4660 mm2 t = 9.5 mm Fy = 248 MPa Fu = 400 MPa Properties of 20 mm A-325 bolts: Fu = 400 MPa 50 50 50 50 50 50,50 힝힝이어 Gusset Plate 9.5mm 100mm Gusset Plate 100mm 31.25 62.5 T 56.25 a. Nominal dimension of hole diameter, dn = 25 mm b. Determine the ultimate shear capacity (kN) of the connection. c. Determine the ultimate tearing capacity (kN) of the connection if the shear lag factor, U = 0.75.
10. What is the net section area of steel plate 40cm wide and 10mm thick with one bolt if diameter of bolt hole is 18mm? a) 38.2 cm² b) 24 cm² c) 578 mm² d) 465 mm2
Please Make a correct table and estimate ( will surely give a like if correct)
Right support: Elasticity= 374 Gpa Left support: Elasticity= 274Gpa Elongation= 9mm Answer item 1 only.
In mm) Problem 8: A C310 × 45 is connected with 25mm diameter bolts in each flange, as shown in Figure, Problem 11. If Fy = 345MPA, Fu = 450MPA, and Ae = 0.90An, Apply the following %3D %3D %3D approaches to determine: a. The design strength for LRFD. b. The allowable strength for ASD. Section Figure. Problem 8
Determine the design strength of an UNP200 with four lines if 16 mm diameter bolts in standard holes, as shown in the Figure below. F = 370MPA F. = 240MPa 60 80 60 100, 100, 100, 100,100 UNP 200
b) In engineering practice, it is often required that two sheets or plates are joined together and carry the load in such ways that the joint is loaded. Many times, such joints are required to be leak proof so that gas contained inside is not allowed to escape. A riveted joint is easily conceived between two plates overlapping at edges, making holes through thickness of both, passing the stem of rivet through holes and creating the head at the end of the stem on the other side. Discuss each of the rivet joints listed below: i) Tearing failure of plates ii) Bearing failure of rivets 2 iii) Shear failure of rivets iv) Splitting/cracking failure of plates at the edges
Tension Member -Problem 2 9 - 4" Bolts Gusset Plate Plate thickness t = ½" 2" Tension Member A36 Steel Plate 3" P, 10" и 3" d h Compare Tension Capacity of line 2" e abcde and line An Ag fgchi 4" 4"
aljall dalla E What is the name of the joint shown below? hp
a] Compute LRFD 6.) Compute ASD CIVIL STEEL DESIGN ENGINEERING- BOLTED CONNECTION Sample Problem 5: The 175 x 100 x 16 mm angle shown connected to a gusset plate with three 25 mm bolts (A490) when threads are excluded from shear planes. The angle consists of A36 steel. Properties of 4 175 x 100 x 16 A36 Steel Properties of A490 bolts A = 4181 mm² t = 16 mm Fy = 248 MPa F₁ = 400 MPa Fy = 276 MPa Nominal hole dia. = 27 mm 75 T+ 100 Gusset Plate 100 F 100
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
round off final answer to 4 decimal places