1, Two parallel disks, 80 cm in diameter, are separated by a distance of 10 cm and completely enclosed by a large room at 20°C. The properties of the surfaces are T1 = 620°C, E, = 0.9, T2= 220°C, E2= 0.45. What is the net radiant heat transfer with each surface? (Do not include back side exchange, only that from the surfaces facing each other.)

1, Two parallel disks, 80 cm in diameter, are separated by a distance of 10 cm and completely enclosed by a large room at 20°C. The properties of the surfaces are T1 = 620°C, E, = 0.9, T2= 220°C, E2= 0.45. What is the net radiant heat transfer with each surface? (Do not include back side exchange, only that from the surfaces facing each other.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve this problem asap .
Consider steady heat transfer between two large parallel plates at constant temperatures of T1 = 500 K and T2 = 300 K that are L = 2.5 cm apart. The emissivity of the surfaces, ɛ = 0.95. Calculate the total rate of heat transfer and the percentage by thermal radiation between the plates per unit surface area assuming the gap between the plates is (a) filled with atmospheric air (k = 0.02 W/m.°C), (b) evacuated. %3D %3D %3D O = 5.67 x 10-8 W/m².K4
A 30-m-long hot rod (Diameter = 100-mm) is placed inside a room whose walls and air are at 25 C. The surface temperature of the rod is 150 C. h=10 W/m K. The surface emissivity is: your student number/10. What is the rate of heat loss from the rod? student number =201810372 %3D
A mectal cylinder of 5 cm in diameter and initially at a temperature about 150 °C. the eylinder is suddenly immersed in liquid with temperature at 50 °C and heat transfer coeflicient about 2000 W/m.°C. Under typical operation conditions the center temperature and surface temperature are measured to be 110 °C and 90 °C after 1 minute, respectivielly. Calculate the thermal conductivity for this material.
1) Draw the thermal resistance network representing heat transfer through the shell. 2) Determine the heat rate transfer under steady state conditions (W) 3) Determine the emissive power being emitted from the outside of the cylindrical tank (W). You can ignore emission from the top and bottom surfaces.
With the aid of a suitable diagram, differentiate the processes of heat transferred by a conduction and a force convection.
= A processing plant is convectively heating a solid half-sphere of radius of 12 cm made of pure aluminum (k 237 W/m-K) by placing it on an insulated surface as shown in Fig. 1. It is exposed to hot exhaust gas at 300°C with a convection coefficient of 180 W/m².K. Is the lumped capacitance approximation valid? Figure 1: Half-sphere
. A hollow sphere with an outer diameter (d,) of 4 cm and outer diameter of 12 cm is kept at an inner surface temperature (T,) of 383 K and outer surface temperature (T,) of 323 K. Calculate the heat transfer and temperature at d = 8 cm. The thermal conductivity of the sphere is 150 W/m°C.
A horizontal steam pipe with an outer surface temperature of 98°C and an outer diameter of 8 cm is covered with a 3 cm thick insulating layer with a surface emissivity of 0.7. The surface temperature of the insulation is 50°C, and the pipe is placed in a 15°C room with atmospheric still air at the same temperature. Calculate: a) Total heat loss from the 12 m length of pipe. b) Thermal conductivity of insulator. Use the empirical correlation for natural convection given below for horizontal cylinders. h=1.24 (AT)3
The horizontal roof of a building has an emittance of 0.9. Air temperature is 1oC on a clear night. Sky acts as a black radiation sink at -60o If the underside of the roof is well insulated, estimate the roof temperature. Assume a convective heat transfer coefficient of 5 W/m2 K.
A processing plant is convectively heating a solid half-sphere of radius of 12 cm made of pure aluminum (k 237 W/m.K) by placing it on an insulated surface as shown in Fig. 1. It is exposed to hot exhaust gas at 300°C with a convection coefficient of 180 W/m2.K. Is the lumped capacitance approximation valid? Figure 1: Half-sphere