1- The use of lubricant in wire drawing dic. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum.

1- The use of lubricant in wire drawing dic. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following information is given for n-pentane at 1 atm:boiling point = 36.20°C ΔHvap (36.20°C) = 357.6 J/g melting point = − 129.7°C ΔHfus (−129.7°C) = 116.7 J/g specific heat gas = 1.650 J/g ⋅ °C specific heat liquid = 2.280 J/g ⋅ °C A 26.10-g sample of liquid n-pentane is initially at −51.40°C. If the sample is heated at constant pressure (P = 1 atm), how many kJ of energy are needed to raise the temperature of the sample to 65.30°C?
Whiteware, porcelain, bricks and bio-ceramics are an example application derived from ceramic materials and undergoes thermal treatment. Briefly explain three (3) thermal treatment for ceramic materials.
A galvanized steel sheet has a zinc coating 20 um thick. The corrosion current density is found to be 4m A/cm2. What is the corresponding duration of rust resistance provided by this system?
Using the information available in Table 2.3, calculate the volume of the unit cell of copper in cubic meters.
An aluminum pipe has a length of 54 m at a temperature of 10°C. An adjacent steel pipe at the same temperature is 8 mm longer. At what temperature will the aluminum pipe be 24 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
A magnesium-lead alloy of mass 6.4 kg consists of a solid a phase that has a composition just slightly below the solubility limit at 300°C (570°F). The magnesium-lead phase diagram is shown in Animated Figure 9.20. (a) What mass of lead is in the alloy? i kg (b) If the alloy is heated to 400°C (750°F), how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? kg
An aluminum pipe has a length of 69 m at a temperature of 8°C. An adjacent steel pipe at the same temperature is 5 mm longer. At what temperature will the aluminum pipe be 15 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×10-6/°C.
What would you expect if you have a 6061 aluminum alloy bar, heat it for 1 hour in the oven forming a single phase, then severely temper it in water and then heat it at 150 ° for 6 hours. ? a) ductility is increased b) increases yield stress c) hardness is reduced d) the material is over-aged and the yield stress is reduced
3.11 Each of the following statements describes a silicate mineral or mineral group. In each case, provide the appropriate name. a- The most common member of the amphibole group. b- The most common non ferromagnesian member of the mica family. c- The only silicate mineral made entirely of silicon and oxygen. d- A high-temperature silicate with a name that is based on its color. e-Characterized by striations. f- Originates as a product of chemical weathering.
Carbon tetrachloride is an organic compound known with the chemical formula CC14. It is also known by many names such as tetrachloromethane by the IUPAC, carbon tet in the cleaning industry, Halon 104 in fire fighting, and Refrigerant-10 in HVACR. CC14 was formerly widely used in fire extinguishers, as a precursor to refrigerants and as a cleaning agent. It is a colourless liquid with a sweet smell that can be detected at low levels. It has practically no flammability at low temperatures. Michael Lobarbio, a very curious student, decided to determine the fluid properties of the abovementioned liquid. In the laboratory, complying with all safety protocols, he weighed a 40 L sample of carbon tetrachloride and obtained a mass of 63.60 kg. As his classmate, it is your task to help him compute the following quantities: (a) density (in g/cm3 ); (b) specific weight (in kN/m3 ); (c) specific volume (in cm3 /g); and (d) specific gravity.
The heater of the automatic defroster in a refrigerator is a resistance wire.The heater uses 110 volts and draws 4.8 amperes of current. Find in ohmsthe resistance.
34 If the following diagram represents the sintering of the ceramic MgO, what could the curves x and y refer to? increase in property X 1000 1200 1600 sintering temperature (°C) (A) = grain size; y porosity (B) x grain size; y = strength O(C) x porosity; y-grain size 1400 O (D) x strength; y grain size 1800