1 In the figure shown, if the elevation at index contour "A" is 3100 meters, and the horizontal distance between "B" and "C" is 2.8 km. (NOTE THERE ARE ONLY THREE INTERMEDIATE CONTOUR IN THIS PROBLEM) e) It is required to produce a miniature relief model of the contour, what will be the height of the miniature (from point "B" to "C") if the scale is 1:300? 0.750 m 1.000 m None of the Choices 1.500 m 2.000 m 1.750 m 1.250 m 2300

1 In the figure shown, if the elevation at index contour "A" is 3100 meters, and the horizontal distance between "B" and "C" is 2.8 km. (NOTE THERE ARE ONLY THREE INTERMEDIATE CONTOUR IN THIS PROBLEM) e) It is required to produce a miniature relief model of the contour, what will be the height of the miniature (from point "B" to "C") if the scale is 1:300? 0.750 m 1.000 m None of the Choices 1.500 m 2.000 m 1.750 m 1.250 m 2300

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter15: Site Plan Layout

Section: Chapter Questions

Problem 15.25Q

See similar textbooks

Similar questions

1. The accompanying tabulation gives elevations of points over the area 30m by 30m city lot. The following elevations were obtained: ( В POINT ELEVATION A 855 m В 880 m C 868 m 896 m C Determine the following: a) Plot the contours using a scale of 1cm=10m with a contour interval of every 10 meters. All corner designations and corresponding elevations must be indicated, including all vertical and horizontal lines. Indicate the following Index contours: 860, 890. The thickness of the index contours must be drawn about twice the thickness of intermediate contours . b) Compute for the horizontal distances of each contour found between two points. Show your complete solution. -
I want Top, Front and Side view of this sketch.
Q1) Draw contour lines of 301.2m, 301.6m, 302m, and 302.4m by interpolation method, with scale 1:200. RLs shown in the table below. All dimension and RLS are in meter. Station 1 2 3 6 7 S 0 10 11 12 13 14 15 16 17 18 19 20 21 24 25 RL 301 3 301 42 301 54 301.75 302 302.05/ 301.94 301.79 301.61 602 $1 301.74 301.68 301.78 301.96 302.16. 302.20 301.96 301 S1 301.63 301 51 301.50 301.77 302 01 302.21 302 38 15 16 25 14 124 13 18 23 301.542 12 22 5 m 10 11 20 21 5 m
Use the following Station/Elevation data to draw a profile view: 1- Fill the NGL values in the profile view. 2- Draw NGL using a vertical scale 1:100 and horizontal scale 1:000. 3- Design your FGL as appropriate. 4- Find the values of FGL on each station. Station 0+000 0+020 0+040 0+060 0+080 0+100 0+120 0+140 0+160 0+180 0+200 0+220 0+240 0+260 0+280 0+300 0+320 0+332.5 Elevation 677.52 674.77 673.82 672.22 672.00 670.04 666.58 667.02 667.79 668.58 670.37 673.52 673.89 673.00 671.69 668.55 667.88 667.03
Create a 3-dimensional isometric projection based on the 2-dimensional orthographic projection below
Q2) From the figure below,draw a contour map with scale 1:600 and contour interval (2m). The area of each square (576m²). 30.7m 32.5 34.4 34 31.2 32.0 35.0 33,4 31.0 33.2 33.4 32.8 28.8 32 30.6 32.2 1
Compute all the interior angles of the given figure:
i need the answer quickly
Compute and illustrate the cross-sectional area. (Use trapezoidal rule)
i need the answer quickly
Q5A)The figure below represent a grid for a parcel with (25 m x 25 m) sub-grid dimension Draw the contour line with elevation=40 00 m using a horizontal scale =1/500 33.14 m 42.24 m 32.22 m 35.74 m
What is tangent modulus?