1) Determine the Centroid of the Shaded Area, Tabulate your answers and solution. Y 450 mm 300 mm r = 200mm 75 mm **Units in mm 300 mm 150mm 75 mm 50 150 50

Q: Volume ama the itCTIlal CHcrgy. 4. A vessel of a volume 0.03m3 contains dry saturated steam at 20…

A:

Q: If the manometer is open to the atmosphere, what is the pressure at C water (p = 1.0 g/cm³) A ct B…

A:

Q: If the applied load F has a size of 300 N, find the tension in the 3 supporting ropes 34 2 2ft 5# 45…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 800…

A:

Q: 10 kg/s of air enters the turbine at a pressure of 120 MPa and 910 K. The air expands Isentropically…

A: Given data m=10 kg/sP1=120 MPaP2=25 MPaT1=910 K

Q: Ticance? n of equality of variance at 5% [ nce interval for the difference be

A:

Q: A particle moves along the path whose equation is r = 20 ft. If the angle 0 = t² radians, determine…

A:

Q: Convert the decimal number 35710 into its octal number equivalen

A: Steps Write the given decimal number. If the given decimal number is less than 8 the octal number…

Q: PROBLEM 2 The elements of a floor jack are shown in the figure. If the hydraulic cylinder AB is…

A: Given DataFAB=37kNTo findL=?FEF=?FC=? ***As per our company policy we are supposed to do only three…

Q: Problem Number 2: In the given flexible cable set-up carrying a uniformly distributed load spread…

A:

Q: Take o, = -400 kPa, Tzy = -330 kPa. (Figure 1) Part A Determine the equivalent normal-stress…

A:

Q: Given the Truss as shown below. Using Method of Joints, determine the forces at the members AB, BC,…

A: Find the force in each members.

Q: Question 1 If the tension in the cable is F = 700N, determine the magnitude of the moment produced…

A: In text F = 700 N but in given data and answer column , F = 750 KN  so I am taking F= 750 KN

Q: Complete the following Table (Show all work.) P T V 200 °C H₂0 R-134a H₂0 R-134a H₂0 R-134a H₂0 800…

A:

Q: PART 1: ANALYSIS OF BEAMS QUESTION 1. Given the simple beam ABC, determine the reaction at the hinge…

A:

Q: 2.) An Isothermal process is done on air, and it has a pressure of 500 kPa and a volume of 0.5m3.…

A:

Q: Question 8 A steam engine isentropically expands 9.308 kg/s of steam from 0.68 MPa, 220°C. the…

A: Find the non flow work for the isentropic process.

Q: 1. Find the number of degrees of freedom for Mechanism with higher pair (h20) in(l-6; j-8): (n=-2;…

A: Note: As per the guideline, I can answer only one question and in question 1 higher pair should have…

Q: A force F with a magnitude of 200 N is applied at the origin O of the axes x-y-z as shown. The line…

A:

Q: Determine the magnitude Fand direction 0 (measured clockwise from the positive y-axis which is…

A: Answer: (a) F = 12.6101 kN. (b) θ = 68.6595°.

Q: The teeth of the gear arrangement have Gear A = 40 teeth, Gear B = 70 teeth, and Gear C = 50 teeth,…

A: Find  Pitch circle diameter of Gear C.

Q: Table 4 shows the fatigue data of a ductile cast iron to be used for an automobile axle that rotates…

A: (a) Draw an S-N curve i.e. stress amplitude versus the logarithm of the number of cycles before…

Q: The truck shown is used to deliver food to aircraft. The elevated unit weighs 2400 lb vwith center…

A:

Q: PROBLEM # 3 1. A solid block is 70 cm wide, 80 cm long and 20 cm tall, and Estimate the solid block…

A: Solid Block

Q: 1. Determine the component of each force along the specified x - y axes. Refer figu 1. the exclusive…

A:

Q: Given a parametric parabolic trajectory of x = 56t and y = 76t - 4.9t2 where x and y are measured in…

A:

Q: 9. Determine the magnitude and coordinate direction angles of the resultant force 600 N 500 N 4 m 4m…

A: Find the magnitude and direction angles of resultant force.

Q: 3. Consider the force system in equilibrium shown in the image below. Determine the following: a.…

A: To draw the free body diagram.

Q: Stainless steel 316 pin fins are designed for use in industrial cooling. The fins will be subjected…

A:

Q: The forces acting on a 1-ft length of a dam are shown in Figure 1-62. The upward ground reaction…

A: Given data as per the question Horizontal force at A side =12500 lb Vertical force =30000 lb The…

Q: A certain amount of an ideal gas is initially at a pressure p, and temperature T,. First, it…

A:

Q: Calculate the x- and y-coordinates of the centroid of the shaded area. y

A:

Q: 5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at…

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A: P = 3.9 kNE = 210 GPa I = 5 * 106 mm4a = 1.5 mb= 1.3m

Q: 5. A gas expands by 1.2 L at a constant pressure of 2.5x105 Pa. During expansion 230 J of heat is…

A:

Q: 1. A rotating cylinder viscometer was used to find the dynamic viscosity of SAE 10W-30 oil at 130°F.…

A: To find: The dynamic viscosity of SAE, and also find the power required to rotate the cylinder at 50…

Q: dy Use the modified Euler Method to solve the ODE dx subject to y = 1 when x = 0 1+x %3D on the…

A: Given, dydx=y21+x=fx,y yx=0=1 h=0.1

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.