Electrical Engineering1) Design an active band-reject filter that has gain 13 and the stop frequency between129 and 1950 Hz. Use 0.235 µF capacitors.R2R1www HFCViVoR1 CWHViOUDVo2) Find R2 and R1 values in the above active High-pass filter for gain of 10 and cutofffrequency of 500 rad/s, when R2 = 359K, R1 = 16K and C = 0.8 µF.wwwOUTR2www

Given Two questions on band reject filter and high pass filter. Please find the below attachment…

1) Design an active band-reject filter that has gain 13 and the stop frequency between 129 and 1950 Hz. Use 0.235 µF capacitors. R2 www R1 C HF A Vi OUTD Vo R2 www R1 www HF Vi OUT Vo Find R2 and R1 values in the above active High-pass filter for gain of 10 and cutoff frequency of 500 rad/s, when R2 = 359K, R1 = 16K and C = 0.8 µF. C

1) Design an active band-reject filter that has gain 13 and the stop frequency between 129 and 1950 Hz. Use 0.235 µF capacitors. R2 www R1 C HF A Vi OUTD Vo R2 www R1 www HF Vi OUT Vo Find R2 and R1 values in the above active High-pass filter for gain of 10 and cutoff frequency of 500 rad/s, when R2 = 359K, R1 = 16K and C = 0.8 µF. C

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

This is an LTI Second Order Subject: Passive Low Pass Filter. Please show the step by step solution for each problem asked. If you managed to do this then I will give you an upvote for your answer and failing to do this will give you an downvote. 1.) Solve for the Voltage Out of given circuit below using circuit analysis. The given values are already displayed. The answer should be around 330mv. Show your solution step by step. 2.) Solve for the Voltage Out again but now with using the transfer function I have obtained below. If you used magnitude below please explain why did you use magnitude and square root please explain the concept behind that. note: Please don't use the solution in bartleby because I found them wrong. Especially the one who used degrees on it.
Given a bandpass filter, Identify the cutoff frequencies
For the low-pass active filter shown below, the transfer function is expressed as: V. Zc V: ZR + Zc where: 106 Zc ja rad w = angular frequency in ZR = 2000 ZR V. Vị - Zc Vo can be written as: Vi 4-A) Show that the Vo 500 Vị 500 + jw Vo What should be the value of w so that the magnitude of Vi is ? 4-B) 4-C) With w = 1250 rad/s, and V; = 9ej1.8 – j10 volts, evaluate the magnitude and phase of V. Vo (Hint: evaluate 2 in polar form, and Vị in polar form, then V, = 2x V; ) Vị 4-D) When 4 modules of this filter are cascaded, the total transfer function will be (2) . Use de Moivre's Theorem to find the expression of the total transfer function in polar form. Then, find determine the value of w so that the magnitude of the total transfer function is ? V10
1. For the circuit in the figure below, obtain the transfer function output voltage / input voltage. Identify the type of filter and determine the corner frequency. Let R1=1000, R2=100N, and L=2mH. R1 L R2 v,(t) |(1)'a ww
Using the series RLC circuit, yield a band reject filter with a bandwidth of 240 Hz and a center frequency of 740 Hz. Use a 100 nF capacitor. The value of w2 is
1) Please solve with work, explanation would be great. Using to study. Will upvote!
You are asked to design an active low pass filter with cutoff frequency 96 Hz. Given a capacitor of 58 nF, specify the value of the R₂ resistor of the low pass filter below. Please enter your answer to the nearest whole number. C Vin R1 www R2 Vout
The following data shows the output voltage of an active filter versus frequency Vo=F(f). Determine the cutoff frequency or frequencies? F(Hz) 100 500 1K 2K 5 K 10 K 15k 20 K 30 K 50K 100k 200k 300k VOV) 0.01 0.035 0.07 0.15 0.32 0.51 0.57 0.57 0.49 р.35 0.10 0.05 0.01
Q.) What type of filter is the given circuit?
Please solve with work
Vo1 R Vin Vo2 C In RC circuit shown, R=4542 and C=3µF, if the output taken across the capacitor (Vo2) then the filter type and the cut-off frequency in rad/sec are; O A. Low Pass Filter and w=1468.43 B. High Pass Filter and w=734.21 O C. High Pass Filter and w=1468.43 O D. None O E. Low Pass Filter and w3734.21
Please I want solution of this question in detail. Thanks