The circuit shown in Figure is a second order low-pass filter. This filter circuit is called a multiple-loop feedback filter (MFF). The output impedance of this filter is zero, so the MFF low-pass filter is suitable for use as a filter stage in a cascade filter. The transfer function of the low- pass MFF filter is H (5) = 52 + 1 R1R3C1C2 1 1 + R2C1 + R3C1 5 + 1 R2R3C1C2 R2 C2 R3 R1 v1) volt) Let R2 = R3 = R and C = C2 = C = 0.05 µf. Design this filter to have wo = 2500 rad/s and Q = 8. What is the value of R, R1 and the dc gain? R = k2, R1= k2, k =

The circuit shown in Figure is a second order low-pass filter. This filter circuit is called a multiple-loop feedback filter (MFF). The output impedance of this filter is zero, so the MFF low-pass filter is suitable for use as a filter stage in a cascade filter. The transfer function of the low- pass MFF filter is H (5) = 52 + 1 R1R3C1C2 1 1 + R2C1 + R3C1 5 + 1 R2R3C1C2 R2 C2 R3 R1 v1) volt) Let R2 = R3 = R and C = C2 = C = 0.05 µf. Design this filter to have wo = 2500 rad/s and Q = 8. What is the value of R, R1 and the dc gain? R = k2, R1= k2, k =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Break frequency is 1000 Hz, filter resistance is 318 Ohms Only do question 2
Circuit Theory
These 5 parts are for one question
1Da Design a second order Low-Passfilter with C15H2) cut-off frequency and (162) Load resistance ifqyou Kinow Ciand Ca=louf 2-Desigh a secandorder hight-eass filter with (225 Hz) Cut-off freauency and C16r2) Load resistance ifyou Know Ciaud C=l04f
a simple Circuit with R =50 ohm and L = 200mH would be a) high or low pass filter? and b) with f0 = ?
a) What type is the active filter shown in the following figure? b) Determine the roll-off rate. c) Find the values of the unknown resistors and capacitors to implement an equal value Butterworth response with an f. = 1 KHz if the damping factor for this configuration is DF = 1.414. (Assume R2 = 1 KN) CAI RAI RB1 Св R1 R2
In the circuit in the figure, Vin=30Vrms and Vout are taken from the C1 capacity. Accordingly, a) Filter find the type b) Find the cutoff frequency (fc) of the circuit c) A=Vout/Vin for f=100, 800 and fc values draw the curve?
A low pass filter is designed to have dB/decade. The cut off frequency is 200 Hz, and the maximum gain of the filter is 23 dB. Determine the ff: a roll off factor of 40 a. Power in dB at the cut off frequency. b. Power in dB at 4000 Hz. c. Frequency that has a power of -20 db.
Required information The circuit shown in the given figure is an active filter. Assume C=15 nF. Ro 4 kohm, R₁-1.2 kohm, R₂ =29.4 kohm, and R3=97.7 kohm. NOTE This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. ww www R₁ C Determine the cutoff frequencies www 20 The cutoff frequencies w₁ and 2 are X 103 and 104, 4, respectively.