1) Consider the column below. If both sections are made of a steel with the Modulus of Elasticity of 200 GPA, calculate the stresses in both sections and the movements (displacements) of B and C. (Learning Activity: L06) 1 m 1.5 MN + B C 2 MN 1.5 MN 30 cm Cross Sectional Area BC: Hollow Circle with 2 cm thickness 60 cm

1) Consider the column below. If both sections are made of a steel with the Modulus of Elasticity of 200 GPA, calculate the stresses in both sections and the movements (displacements) of B and C. (Learning Activity: L06) 1 m 1.5 MN + B C 2 MN 1.5 MN 30 cm Cross Sectional Area BC: Hollow Circle with 2 cm thickness 60 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure below shows a thin-walled cold rolled steel cross-section. The thickness of all segments of the member is 0.105 in. 7 in 7 in 5 in – x' 5 in Determine the moments of inertia of the cross-section I, I, and J, in in* with respect to the centroidal axes x' and y' and the corresponding radii of gyration in inches. in4 in4 in4 Kx' in %D Ky. kc in in II I| || ||
The figure shows a cutaway view of an assembly in which a solid bronze [G= 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d₁ = 1.55 in. The outside diameter of the tube is D₂ = 2.8 in. and its wall thickness is t₂ = 0.115 in. Overall dimensions of the assembly are a = 35 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 9800 psi and 8500 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.2°. Based on these constraints, what is the maximum torque Tg that can be applied at end B? Fixed End plate plate di TB Rod (1) D₂ Answer: TB = A Tube (2) a lb-in b B
In the truss system shown in the figure below, there are totally nine bars. Pick any six of them and calculate the forces they are bearing. Put your answers in the table below. Show your analysis. E Force Compression/ Bar magnitude Tension 4 m 45° АВ AC A 7 m AD 90 BD 3 m 90° CD CF B F CE 4 m 4 m DF 30 N FE
Solve for M/I
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.72 mm the values of elastic modulus for steel is 223 MPa. Take H1 = 7 cm, H2 = 10 cm, top bar (R) is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
Building material H.W1
Solve step by step in digital format please
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 448 mm2, 622 mm2 , and 265 mm2 respectively.Determine the change in length (in mm) of the bar if P = 27199 N.The moduli of elasticity are 81.82 GPa for bronze ,73.92 GPafor aluminum , and 204.55 GPa for steel .
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
i need the answer quickly