1-70. The jib crane is pinned at A and supports a chain hoist that can travel along the bottom flange of the beam, 0.3 m s x < 3.6 m. If the hoist is rated to support a maximum of 7.5 kN, determine the maximum average normal stress in the 18-mm-diameter tie rod BC and the maximum average shear stress in the 16-mm-diameter pin at B. D B 30° 7.5 kN 3 m Prob. 1-70

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: ∑Mx=0Ta+Tc-3X5=0                           (1) COMPATABILITY,…

Q: The way to the column where the loading status is seen determine the P load required for the 5 mm…

A: Given that,

Q: The cantilever strut is subjected to the point loads P1 = 1.4 kN and P2 = 2.8 kN. Determine the…

A: A loading beam With LoadsP1=1.4 kNP2=2.8 kNTo determine: Shear stress at point B

Q: 2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the…

A:

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free…

A:

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

A:

Q: Q4/ The aluminum bracket A is used to support the centrally applied load of 8 kip. If it has a…

A: Now draw the free body diagram of bracket,

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: 1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow =…

A:

Q: F The shaft is loaded with two forces as shown and is fixed at A. The strength is defined as the…

A: The given problem involves analyzing the strength of a shaft subjected to two forces and determining…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1= 11 kN= 11000 N a= 250 mm b= 100 mm c= 90 mm θ= 40∘ Diameter, d= 29 mm Thickness, t= 31 mm   To…

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.