1-55 A planar truss system has the dimensions shown in the figure. Member AE is continuous and can resist bending. All joints are pinned. Determine the diameter required for tension member AB to carry the applied force at A. The allowable stress is 40 ksi.photo of the diagram is attached with the question. 1-55. A planar truss system has the dimensions shown in the figure. Member AEis continuous and can resist bending. All joints are pinned. Determine the diameterrequired for tension member AB to carry the applied force at A. The allowablestress is 40 ksi.B16CE100 Ib10-10----12"Fig. PI-55

1-55 A planar truss system has the dimensions shown in the figure. Member AE is continuous and can resist bending. All joints are pinned. Determine the diameter required for tension member AB to carry the applied force at A. The allowable stress is 40 ksi.

1-55 A planar truss system has the dimensions shown in the figure. Member AE is continuous and can resist bending. All joints are pinned. Determine the diameter required for tension member AB to carry the applied force at A. The allowable stress is 40 ksi.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross-sectional area of each member of the truss is 1200 mm² and the allowable stresses are 100 MPa in tension and 80 MPa in compression. Calculate the maximum value of P the truss can carry. 5m 0.75 m 4 m 3 m B P
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E K 1 kN 1m H M F
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
Chek which is correct.
9. Find the stresses in members BC and BE for the truss shown. The cross-sectional area of each member is 3780 mm². Indicate whether the stresses are tensile (T) or compressive (C). BC = 4.44 MPa (C), BE = 3.45 MPa (T) B C 50° 50° 50⁰° E 20 KN 50% D
For the steel truss (E=29 × 106 psi) and loading shown, determine the deformations of members AB and AD, knowing that their cross- sectional areas are 4.0 in2 and 2.8 in2, respectively. It is given that P= 50 kips. P A B 8 ft D C -13 ft- -13 ft- The deformation of member AB is - in. The deformation of member AD is in.
A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 9 kN is applied at pin B as shown. The angle 0 =38 deg. and the angle ẞ = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final result) · 12mm 9 20mm -1.0m⋅ B
Draw the free body diagram. Do not round off between your solutions and box your final answer up to 4 decimal places
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E Ук 1 kN 1m H F Figura 3. Cercha 3. 2.Determine the force in the elements ED, EH, and GH of the reinforcement (see Figure 4), and establish whether the elements are in tension or compres- sion. (Use the method of sections). Figura 4. Cercha 4. 50 kN 40 kN -2 m -2 m- -2 m- 1.5 m -30 kN 1.5 m B 40 kN 1.5 m