02. Draw a neat sketch (closed traverse) for this note book entry. D 55 40 C24 24 30E B22 10 A

Q: A line was measured using a tape that is suspended with a pull of 145 N on both ends. The mean…

A:

Q: Problem 2: A steel pressure vessel with radius r (used approximately as inner, median and outer…

A: Given :

Q: Problem 1 A - 4% grade meets a +5.5% grade at a vertex whose elevation equals to 132.56 m directly…

A:

Q: Line A B C 9. Fill in ONLY the seven (7) grayed blanks in the following form. Dep. Corrected…

A: Solution: Convert to whole circle bearing: Line Bearing Whole circle bearing AB N 57o 34' E 57o…

Q: 17. COMPLETE THE FOLLOWING INSERT CODE IN INCHES: MG 43 18. COMPLETE THE FOLLOWING INSERT CODE IN…

A: 17. It is made up of  CNMG432       1/2" inner circle , 1/32" corner circle and 80°  Diamond woth 0°…

Q: 0+365 0+370 0+375 0+380 BM2 1.008 0.953 0.880 0.800 0.783 COMPUTATIONS: 1. Computing Height of…

A: The formulas to be used are given in question

Q: slope. It has a side slope of 2:1 and the base width of the roadway is 12 m. (a) Compute the volume…

A: Side slope = 2:1 Base width = 12 m For station 10+110,    Cross section…

Q: Compute the DMD of Line 1-2

A: Answer : DMD ( Double Meridian Distance) of line 1-2 is     -30.

Q: 194.1 201.2 165.4 165

A:

Q: ONS B.S. H.I. F.S. LF.S. ELEVATIONS -a 1.24 234.51m 1.11 3.40 4.6 2.8 3.6 2.4 3.21 2.46 1.2 3.2 2.8…

A: Given profile levelling HI = elevation +   BS elevation = HI - FS or IFS given elevation of BM a =…

Q: The sight distance of a sag parabolic curve is 116.85 m. long with grade tangents of -1.98% and…

A: Parabolic curve

Q: SITUATION. At the exit of a toll gate with a single booth, vehicles arrive at random at an average…

A:

Q: LINES BEARING DISTANCES АВ N 28° E unknown BC Due East 250.62 m CD S 32° E unknown DA Due West…

A:

Q: A 1-m-diameter cylindrical mass, M, is connected to a 2-m wide rectangular gate as shown in the…

A: Given Data- diameter of cylindrical mass=1m width of rectangular gate=2m Required- To calculate the…

Q: Use the CAD drawing below and determine distances A and B to the nearest hundredth inch. + 2 A = O O…

A:

Q: The compound beam consists of three segments that are pin connected at B and E. Sketch the shear and…

A: The beam with the loading and support conditions is given as To find:- Shear force and bending…

Q: Q24. Draw the plan, section and elevation of the given line diagram. W BED Refe re nce W 4000x4000…

A:

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: The following data are the cross section notes at station 12+046.58 and 12+066.58. The natural…

A: (A) A= 20.25 m2 (B) A= 12.8 m2 (C) VC-VF= 70.3 m3

Q: Figure 1 shows an orthographic projection of a block. Draw the object in isometric projection. Show…

A:

Q: 400 Hole of radius 200 300 --> x' 600 - 750

A: we are authorized to answer up to three subparts in one question request. please repost the…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: EXAMPLE 1: Draw the fallowing Figure using the different methods of ends line coordinates…

A: Line Command in AutoCAD: A line is drawn in AutoCAD by following steps given below. Open the…

Q: 4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch…

A: The levelling terms and formula. BS = Back sight The first measurement taken in a survey. It is the…

Q: 42 12 18 48 70 The known: front projection, side projection Required: Draw the three projections 32

A:

Q: The following contains lines AB, CD, and EF. Complete all views. Label lines that are true length as…

A: To Complete all views of lines AB, CD and EF

Q: Q1: Draw the F.V., T.V., and the S.V. for the following isometric shape: R 20 /820. 20 90 45 99

A: Front view and top view, side view are drawn below

Q: 23. Find the radius of the circle inscribed in a triangle formed by the lines 7x+24y-70-0,…

A: Given values: Circle inscribed in triangle formed by lines: 7x+24y-70=0    →i21x-20y-70=0…

Q: A line AB is 40 mm long.Endpoints A & B are 20 mm in-front of Vertical Plane.Endpoints A is 15 mm…

A: Trace is the point of intersection of a line with any plane then that point of intersection is…

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.