:0.3 m, Ko = 0.5 m, k = 500 N/m, and k. 40 N.m/rad, In the system shown, m = where Ko is the radius of gyration of the pulley about point 0. There is no slippage between the cord and the pulley. Replace the system with an equivalent { a) torsional spring and mass moment of inertia at point 0, and b) translational mass and spring at point A. 10 kg, r = т, Ко kt A m www

:0.3 m, Ko = 0.5 m, k = 500 N/m, and k. 40 N.m/rad, In the system shown, m = where Ko is the radius of gyration of the pulley about point 0. There is no slippage between the cord and the pulley. Replace the system with an equivalent { a) torsional spring and mass moment of inertia at point 0, and b) translational mass and spring at point A. 10 kg, r = т, Ко kt A m www

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q3(b) shows a uniform bar AB of mass = 8 kg hinged at point C. Point A is connected to a spring to maintain the bar in vertical direction, and the stiffness k = 500 N/m. If point A is displaced counter-clockwise by a small angle θ = 3.5 degree and released, (i) With the free body diagram and kinetic diagram, determine the initial horizontal displacement of A.
+ b 3. A tuning fork is an example of a "resonant system", that is, one that has a low damping ratio. A model of a (half) tuning fork is rod of mass m with air drag modeled as a damper connected approximately at its middle, and a torsional spring at the base of the cantilever. Assume the cantilever rotates back and forth about its pivot by a small angle o. Because other forces are much larger, you can reasonably neglect the effect of gravity in this model. The moment of inertia of a cantilevered beam pinned at one end is equal to ml2, where I is its length. (a) What is the natural frequency of this system if m= 0.1 kg and k = 2548 Nm/rad, and 1 = 0.1 m. Please give the value in rad/s and Hz. (b) Find an upper bound on the damping coefficient b that insures that the damping ratio of the tuning fork is no greater than = 0.01. (c) For this damping ratio, what is the damped natural frequency of the system? (d) For this damping ratio, what is the decay rate (the size of the exponent…
The homogeneous circular disk shown in Figure A3.4 has mass moment of inertia about its centre of mass of l = 3 kgm². It rotates about a fixed shaft at its centre and is attached to a torsional spring with constant k = 20 Nm/rad. At t = 0, the angle is = 0, the angular velocity is d/dt = 4 rad/s, and the disk is subjected to an oscillatory couple M(t) = 10 sin 2t Nm. Determine as a function of time.. Figure A3.4 M(1)
Q3- For the torsional system shown in fig (3), find : 1. F.B.D. for vibrational system. 2. Drive Kt. Of the system. 3. Equation of motion by energy method. 4. Fn. 5. Acceleration of the system when initial displacement B, and initial velocity =0.
QUESTION 3. Consider the mass-spring oscillator without friction: y" + y = 0. Suppose we add a force x(t) which corresponds to a push (to the left) of the mass as it oscillates. We will suppose the push is described by the function x(t) = -u(t – 2n) + u(t – (2n + a)) for some a > 2n which we are allowed to vary. (A small a will correspond to a short duration push and a large a to a long duration push). Here, u(t) is the unit step function. We are interested in solving the initial value problem y" + y = x(t), y(0) = 1, y'(0) = 0.
5. A rod of length L, Young's modulus E, cross-sectional area A and mass density p is installed as shown. Suppose m = pAL and kL / EA =1. Find the equations of motion Open Question m www f(t) x=0 x = L/2 x= L
4а. Show that the torque t = la, where I is the rotational inertia. Consider the pulley system shown in figure 4. Suppose the pulley is made up of a disc with mass Ma and a ring (hoop) with mass M, as shown in Figure 4a. Find the moment of inertia I, of the pulley through the center of mass. 4b. Find the angular acceleration a, of the pulley as a function of Ip, 0, M1, M2, µk. You may assume that there is no slipping between the pulley and the rope and the mass of the rope is negligibly small in comparison with the mass M1, and M2. The coefficient of friction between M2 and the incline is µk with M1> M2. 4c. Mr md MK outer ving (Mr) Central dise (Ma) RI axis at RAzti on X- Sedi on a pullag
1- Two mass-spring-damper systems A & B. System A has = 0.1 and @n = 20 rad/sec, and system B has < = 0.3 and wn = 5 rad/sec. Which system will vibrate longer in time? Why?
A body weighing 5kg is attached to a very light bar as depicted below. The set-up is free to rotate in the vertical plane about pin support O. The force applied at point C makes the bar oscillate(via small rotation) about the position of equilibrium illustrated below a. Derive the differential equation of motion for the steady state angular displacement (theta) of the bar
a=2 b=2 Dynamics question solve