0.05 kg of a certain gas in a piston and cylinder is compressed reversibly until the pressure reaches 0.615 MPa. The initial pressure and volume were 0.1025 MPa and 0.03 m3 respectively. Determine the final temperature, the work done on the gas, the heat flow to or from the cylinder walls. i) When the process is according to law PV1.4 = C, ii) When the process is isothermal. (the molecular weight of a certain gas is 44 and y = 1.3).

Q: 3.2) An isolated piston-cylinder contains 3 liters of saturated liquid water at a constant pressure…

A: Given: The volume of water, V = 3 litres The pressure of water, P = 200 kPa The work done by paddle,…

Q: A mechanical refrigerating system employing R-134a is operated under such conditions that the…

A: Given data: Refrigerant used is R134a                     Evaporator temperature = 4°C…

Q: H20 R-134a . H20 R-134a H20 R-134a H20 R-134a 1000 150 500 200 500 300 100 200 500 -10 0.05000 200…

A: The following table is shown in the ficture to wrire down the values of specific volume, specific…

Q: During a quasi-equilibrium process, the pressure- volume relationship follows the function below: P…

A: a= -1200 kPa/m^3 b= 600 kPa Pressure volume relationship: ⇒P= aV+b⇒P= -1200V+600 Initial volume, V1=…

Q: As shown in the figure below, Refrigerant 134a is contained in a piston-cylinder assembly, initially…

A:

Q: 1.2 1 kg of a fluid is compressed reversibly according to a law pe 0.25, where p is in bar and r is…

A: Given data Pv = 0.25 Final volume = 1/4 initial volume

Q: 5 kg air with initial temperature of 100°C expands at a constant pressure of 2 bar to reach to a…

A:

Q: For the following process: Saturated liquid water, initially at 25°C contained inside a tank, is…

A: Three single phase zones (liquid, vapour, and supercritical fluid) are represented on the Tv…

Q: Calculate the net work produced by this cycle, the required heat input to the cycle and its thermal…

A: hjjhjhjhkjk

Q: 0.25kg/s of Carbon Dioxide (R = 0.1889 kJ/kg-K, k = 1.289) undergo a certain process in a close…

A:

Q: g air with initial temperature of 100°C expands at a constant pressure of 2 bar to reach to a final…

A:

Q: 0.5 kg of Helium undergoes a cycle in a piston–cylinder assembly. Initial state: 2.2 MPa and 0.3 m3…

A:

Q: Refrigerant 134a is contained in a piston-cylinder assembly, initially as a saturated vapor. The…

A:

Q: 8. A stationary mass of gas is compressed without friction from an initial state of 0.3 m³ and 1.05…

A: The work done during the process can be determined as shown below.   Here, a negative sign…

Q: Q1. Consider a household refrigerator whose interior volume is 0.6 m'and average temperature and…

A:

Q: 0.05 kg of a certain gas in a piston and cylinder is compressed reversibly until the pressure…

A: Given: Mass of the gas (m)=0.05kg Initial pressure of the gas P1=0.1025MPa Initial volume of the gas…

Q: A tank of compressed air is at 40°C and 10 atm. 1 third of the gas is removed for inflating a car…

A: Dear student,                    According to the guidelines I am allowed to answer only three…

Q: 1 kg of steam in a piston / cylinder assembly is initially at 357.933 \ deg C and 2685.66 kPa. It is…

A:

Q: The thermodynamic process the problem represents b. the pressure, temperature, and volume after the…

A: the process is isentropic compression

Q: 0.06m of fluid at 0.6bar is compressed in a polytropic process to a pressure of 3.5bar. The fluid is…

A: Given Data Initial volume is V1=0.06 m3 Initial pressure is :P1=0.6 bar Pressure at point 2 is:…

Q: A closed rigid tank contains 5.5 lbm of Refrigerant 134a, initially at a temperature T = 200°F. The…

A: Let's convert the temperature unit from Fahrenheit to celsiusT1= 200 F = 94oCT2=70 F = 21oCThe final…

Q: 3. 0.1 kg of Water is compressed in a piston cylinder assembly adiabatically. The water starts out…

A:

Q: ) Argon is compressed in a polytropic process with n = 1.2 from 120 kPa and 10°C to 800 kPa in a…

A:

Q: Steam, initially saturated at 2.28 MPa, passes through a 10 cm standard steel pipe for a total…

A: Given: P=2.28 MPaDi=10 cmL=150mtins=5 cmkins=0.043 W/mkT∞=30oCm˙steam=0.15 kg/secho=9.36 W/mk To…

Q: 0.25kg/s of Carbon Dioxide (R = 0.1889 kJ/kg-K, k = 1.289) undergo a certain process in a close…

A:

Q: c) As shown in Figure A1-c, a gas is contained in a piston-cylinder assembly. The mass and the…

A:

Q: In a Piston-Cylinder system, it initially contains 2.8 bar and 40 C temperature R-134a refrigerant…

A:

Q: 0.25kg/s of Carbon Dioxide (R = 0.1889 kJ/kg-K, k = 1.289) undergo a certain process in a close…

A:

Q: Saturated liquid water, initially at 25°C contained inside a tank, is then delivered by a pump at 5…

A:

Q: Water in an open metal drum is to be heated from room temperature (25 C) to 80 C by adding steam…

A:

Q: 3. A gas contained in a piston cylinder. The gas expands slowly from an initial pressure and volume…

A:

Q: A fluid expands reversibly according to a linear law from 3.8 bar to 1.1 bar, the initial volume is…

A:

Q: 0.5 kg of air with a pressure of 2 MPa and a temperature of 250 °C expands while satisfying the…

A:

Q: 0.06m of fluid at 0.6bar is compressed in a polytropic process to a pressure of 3.5bar. The fluid is…

A: Given Data Initial pressure is: P1=0.6 bar Initial volume is: V1=0.06 m3 Pressure at point 2 is:…

Q: b) Air with a volume of 0.031 m³ is trapped in a piston-cylinder assembly at a temperature of 40°C…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.