Steam, initially saturated at 2.28 MPa, passes through a 10 cm standard steel pipe for a total distance of 150 m. The steam line is insulated with 5 cm thickness of fiberglass insulation (k = 0.043 W/m-K). For an ambient temperature of 30°C, neglecting steam surface coefficient, what is the quality of the steam which arises at its destination if the mass flow rate is 0.15 kg steam per second? Note: ho for still air is 9.36 W/m²-K

Steam, initially saturated at 2.28 MPa, passes through a 10 cm standard steel pipe for a total distance of 150 m. The steam line is insulated with 5 cm thickness of fiberglass insulation (k = 0.043 W/m-K). For an ambient temperature of 30°C, neglecting steam surface coefficient, what is the quality of the steam which arises at its destination if the mass flow rate is 0.15 kg steam per second? Note: ho for still air is 9.36 W/m²-K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Create a table showing wrench sizes in metric and U.S. units.
An automobile tire is 65.0 cm in diameter. How fast (rpm) does the wheel turn on the axle when the automobile maintains a speed of 84.0 km/h? Round to two decimal places.
Completely solve and box the final answer. Please show the units to show the unit cancellations. Write legibly 5. Calculate the boiler efficiency if it generates a total of 1,488.105 short tons of steam for a third of the day at a factor of evaporation of 1.35. The fuel has rating of 35 degrees API with consumption rate of 3.858 short tons for quarter of an hour.
Could you please provide me the top, front and right side view of this diagram?
DRAW THE ISOMETRIC FIGURES OF THE ORTHOGRAPHIC DRAWINGS BELOW.ADD DIMENSIONS AND LEADERS
I need help drawing a pictoral of this shape which has the front, top, and side view. Can you sketch it out on some paper ?
Select the correct statement about the notation circled in green and marked as letter C. Assume all dimensions are in inches. 4x375 A с 8.00 Lo A- Hoy 4x5.25 4x 4.75 4x R.70 4x 115.0 4x 1.40 B 4x 2.00 4x 1.20 6.00 25 M₂ 4x.75 4x 25 .75 1.00 Ø6.50 SECTION A-A SCALE 0.400 4
Can you please help me draw the Isometric illustrations from the given orthographic drawing? I will rate Thank you so much.
Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M) 15 20 60 15 45 30 2 HOLES DIA 20 120 30 15 60 F/ 35
Please do not make any mistakes here. Important question
Show your complete solution to the questions given below. State all assumptions used during the Draw relevant figures, if necessary. Do not round off during your calculations. Unless otherwise specified, express your final answer/s to the nearest four decimal If it is a very small/very large number, express your final answer/s in scientific notation to the nearest two decimal places. Box your final answers. Your answer is not considered final if it is not enclosed in a PROBLEM 4 A cooling tower of a centralized air conditioning system handles 5,000 m3/h of water which enters the tower at 40°C. The cooled water leaves the tower at 28°C. The drift loss is 0.1% while the blowdown is 0.4%. The water make-up is 150 m3/h at 30°C. The air blown through the tower enters at 25°C and has a relative humidity of 70%. The air leaves the tower at 35°C with a relative humidity of 95%. Calculate the volume of air, in m3/h at ambient conditions that the forced draft fan of the cooling tower…
Draw the Isometric drawing of the given orthographic projections below. Use drawing scale to fit the drawing in a 4A/short size bond paper