Answered: 0.001kg 1. Water (µ = -)is flowing…

0.001kg 1. Water (µ = -)is flowing through a 3-mm diameter, 9-m long horizontal pipe steadily at 0.6m/s. Determine the regime of m.s flow and solve the pressure drop and head loss through the pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 30 cm above the pipe B. The height of oil in right limb is 50 cm. Also, the mercury level difference is found in right limb as 90 cm. Find the pressure difference between these two pipes in kPa. Also find the pressure equivalent in water head in mm. The difference of pressure between two pipes (PA-PB) (Unit is in kPa) ? Equivalent to Water head in mm ?
Water flow at a 250mm diameter horizontal pipe 875m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 153.68 L/s В No answer among the choices C) Q = 101.07 L/s D) Q = 118.43 L/s E Q = 132.74 L/s F Q = 172.81 L/s %3D
a. Determine the velocity of flow in the pipe in m/s. b. Determine the discharge Q in m^3/s. c. How many meters above the center of the pipe will water stand in piezometer tube 3? d.
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 118.43 L/s В Q = 132.74 L/s Q = 101.07 L/s D Q = 172.81 L/s Q = 153.68 L/s No answer among the choices
8.2
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
Determine the friction loss if the friction factor is 0.4 and velocity of the flow is 40 m per sec. Given length of the pipe is 20m, inner diameter 0.3m. Use friction loss formula. Using the calculated friction loss, solve for the ffg: a. What is the pressure drop due to the Bernoulli effect as the water goes into a 3.00-cm-diameter nozzle froma 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? b. To what maximum height above the nozzle can this water rise? (To actual height will be significantly smaller due to air resistance.)
سنب Fluid mechanics
Q- In a pond at a depth of 5m air bubble is formed of diameter 0.8mm. Calculate gauge pressure inside air bubble. Assume surface tension = 0.075N/m.
UT. LEUMASARY Water flows at a rate of (0.5 m³/s) round a (50) contracting pipe bend which lies in a horizontal plane. The diameter at the entrance is (700 mm) and at the exit (500 mm) as shown in figure (7). If the pressure at the entrance is (200kPa. ), Determine the magnitude and direction of the force exerted by the fluid on the bend. d = 500mm out d=700mm Figure (7 in 50
Orifice meter with orifice cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauges fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of discharge using Cd=0.6.