.53 In the Dumas-bulb technique for determining the molar mass of an unknown liquid, you vaporize the sample of a liquid that boils below 100 °C in a boiling-water bath and determine the mass of vapor required to fill the bulb. From the following data, calculate the molar mass of the unknown liquid: mass of unknown vapor, 1.012 g; volume of bulb, 354 cm; pressure, 742 torr; temperature, 99 °C. 3.

.53 In the Dumas-bulb technique for determining the molar mass of an unknown liquid, you vaporize the sample of a liquid that boils below 100 °C in a boiling-water bath and determine the mass of vapor required to fill the bulb. From the following data, calculate the molar mass of the unknown liquid: mass of unknown vapor, 1.012 g; volume of bulb, 354 cm; pressure, 742 torr; temperature, 99 °C. 3.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A 0.3 L vessel contains 20 mmol of methane gas at 30 °C. What is the calculated pressure of the gas, using the ideal-gas equation (PV = nRT)? [R = 8.314 L kPa mol–1 K–1. Enter your answer as a numerical value in units of kPa.]
A sample of hydrogen (H2) gas was collected over water at 60°C. If the total volume of gas collected was 71.8 mL and the atmospheric pressure was 1.02 bar, what mass (in g) of hydrogen gas was collected above the water? The vapour pressure of water at 60°C is 150 torr.
A 0.265 g sample of a metal, M, reacts completely with sulfuric acid according to M(s) + H,SO,(aq) → MSO,(aq) + H,(g) A volume of 277 mL of hydrogen is collected over water; the water level in the collecting vessel is the same as the outside level. Atmospheric pressure is 756.0 Torr, and the temperature is 25 °C. The vapor pressure of water at 25 °C is 23.8 Torr. Calculate the molar mass of the metal. molar mass: g/mol
A piece of metal weighing 0.713 g was placed in an eudiometer containing aqueous HCI. After the metal fully dissolved ,23.5 mL of hydrogen gas was collected by displacement of water and a 400 mm column of water was observed. The water temperature was 25 degrees Celcius and the barometric pressure was 758.8 mm Hg ( torr). Refer to the introduction and data sheet to solve the following problems. Calculate the pressure of the hydrogen gas above the water in the column. Calculate the volume occupied by the hydrogen gas at STP.How many equivalent weights (#ew) of the metal were consumed in the reaction? What is the equivalent weight of the metal?
What is the temperature in K of 0.500 mole of neon in a 2.00L vessel at 4.32 bar? R = 0.08314 L· bar/mol·K.
A 0.483 g sample of a metal, M, reacts completely with sulfuric acid according to M(s) + H,SO,(aq) MSO, (aq) + H, (g) A volume of 209 mL of hydrogen is collected over water; the water level in the collecting vessel is the same as the outside level. Atmospheric pressure is 756.0 Torr, and the temperature is 25 °C. The vapor pressure of water at 25 °C is 23.8 Torr. Calculate the molar mass of the metal. molar mass: g/mol
A 0.210 g sample of a metal, M, reacts completely with sulfuric acid according to the reaction M(s)+H2SO4(aq)⟶MSO4(aq)+H2(g) A volume of 219 mL of hydrogen gas is collected over water; the water level in the collecting vessel is the same as the outside level. Atmospheric pressure is 1.0079 bar and the temperature is 25 °C. The vapor pressure of water at 25 °C is 0.03167 bar. Calculate the molar mass of the metal.
High-pressure liquid chromatography (HPLC) is a method used in chemistry and biochemistry to purify chemical substances. The pressures used in this procedure range from around 500 kilopascals (500,000 Pa ) to about 60,000 kPa (60,000,000 Pa ). It is often convenient to know the pressure in torr. If an HPLC procedure is running at a pressure of 5.28×108 Pa , what is its running pressure in torr?
5.(a) Assume for the moment that air consist of 80.00% nitrogen and 20.00% oxygen byvolume. Use these figures and typical values for temperature and pressure (1.000atm, 25.0 ºC) to calculate the density of air. (b) This calculation affords a good approximation of the density of air at sea level.However, your lab is at an altitude approximately 777 meters (2550 feet). Knowingthis, will the density of air in you lab be higher or lower than the value you justcalculated? Why? (c) Besides altitude, what else affects the atmospheric pressure? Where could you findthe actual atmospheric pressure at the time of the experiment?
A chemical engineer must calculate the maximum safe operating temperature of a high-pressure gas reaction vessel. The vessel is a stainless-steel cylinder that measures 37.0 cm wide and 44.4 cm high. The maximum safe pressure inside the vessel has been measured to be 5.00 MPa. For a certain reaction the vessel may contain up to 2.57 kg of boron trifluoride gas. Calculate the maximum safe operating temperature the engineer should recommend for this reaction. Write your answer in degrees Celsius. Be sure your answer has the correct number of significant digits. temperature: ºc x10 X S olo 18 Ar 18
If the partial pressure of N2 is 2.70 x 105 Pa and the partial pressure of Ne is 5.00 x 105 Pa in a given mixture, what is the mole fraction of Ne (XNe)?
A mixture consiting of 1.000 mol H2O(g) and 1.000 mol CO(g) is placed ina reaction vessel of volume 10.00 L at 800. K. At equilibrium, 0.665 mol CO2(g) is present as a result of the reaction CO (g) + H2O (g)⇋ CO2(g)+H2(g). What are the value of KC at 800. K?